Filter
Top Products
TTAABBLLEE OOFF CCOONNTTEENNTTSS
Section Page
1.0 Warranty Information .............................................................2
1.1 Radio and TV Interference
1.2 CE Notice
1.3 Service Information
2.0 General Information...............................................................4
2.1 Features
2.2 Description
3.0 Configuration .........................................................................5
3.1 Configuring the Hardware Switches
3.1.1 Reversible Interface Driver Board
3.1.2 Connecting to a “DTE” Device
3.1.3 Connecting to a “DCE Device
3.1.4 Configuring the X.21 Interface Module
3.1.5 Configuration Switch Set “S1”
3.1.6 Configuration Switch Set “S2”
3.1.7 Configuration Switch Set “S3”
3.2 Configuring the Rear Interface Card
3.2.1 Model 1001RCM12545 & 1001RCM125TB Strap
Settings
3.2.2 Model 1001RCM13445 & 1001RCM134TB Strap
Settings
3.2.3 Model 1001RCM11545 & 1001RCM115TB Strap
Settings
4.0 Installation ...........................................................................19
4.1 The Model 1001R14P Rack Chassis
4.1.1 The Rack Power Supply
4.2 Installing the Model 1095RC Series Into Chassis
4.3 Wiring the Model 1095RC Series
4.3.1 Connection to the Twisted Pair Interface
4.3.2 Two-Wire Cable Connection Via RJ-45
4.3.3 Two-Wire Cable Connection Via Terminal Block
5.0 Operation.............................................................................23
5.1 LED Status Indicators
5.2 Test Modes
5.2.1 Overview
5.2.2 Loops and Patterns
5.2.3 Using the V.52 (BER) Test Pattern Generator
Appendix A - Specifications........................................................34
Appendix B - Factory Replacement Parts and Accessories.......35
Appendix C - Terminal Interface Pin Assignments .....................36
Appendix D - Transmission Distance Chart ...............................39
Appendix E - Line Interface Pin Assignments............................40
1
11..00 WWAARRRRAANNTTYY IINNFFOORRMMAATTIIOONN
Patton Electronics warrants all Model 1095RC components to be
free from defects, and will—at our option—repair or replace the prod-
uct should it fail within one year from the first date of shipment.
This warranty is limited to defects in workmanship or materials,
and does not cover customer damage, abuse or unauthorized modifi-
cation. If this product fails or does not perform as warranted, your sole
recourse shall be repair or replacement as described above. Under no
condition shall Patton Electronics be liable for any damages incurred
by the use of this product. These damages include, but are not limited
to, the following: lost profits, lost savings and incidental or consequen-
tial damages arising from the use of or inability to use this product.
Patton Electronics specifically disclaims all other warranties,
expressed or implied, and the installation or use of this product shall
be deemed an acceptance of these terms by the user.
1.1 RADIO AND TV INTERFERENCE
The Model 1095RC generates and uses radio frequency energy,
and if not installed and used properly—that is, in strict accordance with
the manufacturer's instructions—may cause interference to radio and
television reception. The Model 1095RC has been tested and found to
comply with the limits for a Class A computing device in accordance
with the specifications in Subpart J of Part 15 of FCC rules, which are
designed to provide reasonable protection from such interference in a
commercial installation. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If the Model 1095RC
does cause interference to radio or television reception, which can be
determined by disconnecting the unit, the user is encouraged to try to
correct the interference by one or more of the following measures:
moving the computing equipment away from the receiver, re-orienting
the receiving antenna and/or plugging the receiving equipment into a
different AC outlet (such that the computing equipment and receiver
are on different branches). In the event the user detects intermittent or
continuous product malfunction due to nearby high power transmitting
radio frequency equipment, the user is strongly advised to take the fol-
lowing steps: use only data cables with an external outer shield bond-
ed to a metal or metalized connector; and, configure the rear card as
shown in section 3.2 of this manual.
1.2 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates
that it is in compliance with the Electromagnetic Compatibility (EMC)
directive and the Low Voltage Directive (LVD) of the European Union.
A Certificate of Compliance is available by contacting Technical
Support.
2