Filter
Top Products
Pertech Resources Inc. November 2005 220321A 21
After the printer is set up, you can run two print diagnostic reports / tests and
enter the conguration menu. Below is an example of the conguration report.
1 Press and hold the Paper Feed Button and then
press the Power Switch to turn the printer on and
start the rst test.
Validation printers will perform a Self Test if a form is
detected, when the power is turned on.
Release the Paper Feed Button after 4 seconds for
the printing to begin.
The 5300 completes a test of RAM , a checksum
test of program memory, homing and maintenance
of the print head, and then prints the conguration
settings.
2 To change the conguration settings, press the
Paper Feed Button when prompted, the Left LED
will begin ashing.
Note: Validation-Only printers do not have this
feature.
Note: If Ink Status Reset is set to “Manual”, rst
option to print will be “Press feed to Reset Ink Tally”.
A. Entering the conguration mode, the printer prints
the Set-Up Instructions and prompts the user to
press the feed button to reject the current settings.
B. If you don’t want to change an option, wait for ve
seconds and the next option will print.
C. After completing the Conguration Mode, the
printer prints the new conguration settings and
stores them in non-volatile memory.
Note: Exiting setup early by turning the printer off
will erase any changes made to the conguration.
You must complete the setup for changes to take
effect.
Conguration Report & Setup Mode
SerialNumber:
********
MainFirmware
Revision:
******
CRC:
****
BootFirmware
Revision:
******
CRC:
****
PrinterControlLanguage
PCL: ACLLanguage
DiagMode: StandardPrint
AutoLF: CR=CR
SoftFaultRecover: Automatic
Font:
Font: Standard
FontQuality: Draft
IntlCharset: USA
CodePage: 437USA
ReceiptLPI: 6Lines PerInch
ValidationLPI: 6LinesPerInch
RS232Serial(whenused)
BaudRate: 57.6K
DataBits: 8-bits
StopBits: 1-bit
Parity: None
FlowControl: Hardware
USB(whenused)
Descriptor: ModelNumber
Hardware
ValidationClamp: Closed
FormInsertWait: 1Min
PaperLowSensor Enabled
InkStatusReset: Automatic
DocumentStop: 1.75Inches
ColumnAlignment
HalfSpeed: 3
FullSpeed: 10
Memory
InstalledRAM: 128K
InstalledROM: 512K
TotalUserFlash: 64K
FlashLogos 32K
FlashFonts 0K
FlashMacros: 0K
FlashRawData: 32K
TotalUserRam: 24560
RamLogos: 24560
RamFonts: 0K
RamMacros: 0K
Tallies
PrintedLines: 0
DotCount: 0
ValidationOpens: 0
FeedDistance: 0
HoursOn: 0
FlashUpdates: 0
CoverOpens: 0
Diagnostic:
0 0 0
====================================
Press paper feed to change configuration
Press paper feed to enter print test
=================================
Press paper feed to change conguration
SET-UP INSTRUCTIONS
PRESSING THE PAPER FEED BUTTON WHILE THE
GREEN LIGHT IS FLASHING WILL REJECT THE
LAST PRINTED PARAMETER. IF THE BUTTON IS
NOT PRESSED WITHIN 5 SECONDS. THE PARAM-
ETER WILL BE ACCEPTED AND THE NEXT SET-UP
OPTION WILL BE LISTED.
PRESS THE PAPER FEED BUTTON NOW TO
REJECT THE CURRENT CONFIGURATION AND
CONTINUE WITH THE PRINTER SET-UP.
3 Otherwise, wait 10 seconds
and you can choose to enter
an Extended Print Test. After
this test, or Ignoring this
option, will return the printer
to normal operation after 10
seconds.
4. Extended Print Test:Checks the
printers vertical line alignment,
character fonts, and pitches.