Filter
Top Products
Secure MICR Printer User’s Guide © Source Technologies
July 2003 Page 46 All rights reserved
Error Message
on Display Printed Message Description Action
Can’t Purge Pswd not
enabled
Can’t Sort Insufficient
Memory
Command Decode Error
Convert to Esc Error
Flash Full Purge and
Format
Load MICR Toner
Macro Definition Error
Macro Definition Error
Macro Definition Error
Macro Definition Error
Macro Definition Error
Macro Transfer Error
Macro Transfer Error
MICR Definition Error
MICR Password Error
MICR Password Error
MICR Password Error
Security Lock Error
Security Lock Error
This error indicates that MICR mode has not
been enabled.
This error indicates the printer does not
have sufficient memory to sort the Audit
Report.
A syntax error was detected in a MICR
command.
An error was detected in the User
Programmable Escape Character Selection
Command. The software tried to specify a
NULL or an ampersand as the first Escape
Character.
This error message indicates that the
printer’s flash memory is full. The audit trail
cannot accept more jobs until more space
is available in flash.
Before printing a MICR font, the printer
checks for MICR toner. If regular toner is
present, the printer will stop all printing and
display this message.
The Load Flash Resource Command
contained an invalid character specifying
the format of the file. Must be either a D or
S.
The resource number in the Load Flash
Resource Command (&%STL...) was over
the 32767 list.
Flash resource file size specified in the
Load Flash Resource Command is too large
fro the available space remaining in the
flash module.
The Load Flash Resource Command
contained a non-hexadecimal value in the
byte count parameter.
The resource number in the Load Flash
Resource Command (&%STL...) was not
five integers.
The Flash Resource Number in the Secure
Flash Resource Unlock Command was not
five digits in length.
The Secure Flash Resource Unlock
Command contained a non-integer value.
The number of digits in the MICR definition
Command is not equal to four, or there is a
non-hexadecimal character in the count.
Password length is not equal to eight
characters.
Password sent does not match the current
stored password.
Front panel combination feature has been
enabled but was not entered before a MICR
job was started.
An error was detected in the Activate/Set
Front Panel Combination Lock Command.
The combination must be eight digits in
length.
An error was detected in the Activate/Set
Front Panel Combination Lock Command. A
character was received in the command
that was a non-integer.
Press Go. Enter MICR mode, then
re-attempt the purge.
Press Go. The printer may need
to be upgraded with more RAM
memory to sort; otherwise an
unsorted Audit Report may be
printed.
Check your software for a
syntax error in the MICR
command that was being used
when the error occurred.
Check the Command (&%STY...)
for errors.
Press Go then purge the audit
trail. Then either defragment or
format flash memory (Utilities
Menu).
Replace standard toner cartridge
with a MICR Toner. Go to
proceed. If MICR toner is not
available, you must power-off
your printer and restart the print
job at a later time when MICR
toner is available.
Check the Command (&%STL...)
for syntax errors.
Check the Load Flash Resource
Command for syntax/numbering
errors.
Format flash memory to remove
all existing resources or upgrade
flash memory to a larger module.
Check the Command (&%STL...)
syntax for errors.
Check the command for syntax/
numbering errors.
Check the Command (&%STP...)
for syntax/numbering errors.
Check the Command (&%STP...)
for syntax/numbering errors.
Check your software for errors in
the MICR definition Command.
Check the Password Command in
your software, it must be eight
characters long.
Check the Password Command in
your software.
From the front panel select MICR
Menu>Security Lock and enter
the correct combination. Press
Go to resume the print job.
Check the Activate/Set Front
Panel Combination Lock Command
in your software.
Check the Activate/Set Front
Panel Combination Lock Command
syntax in your software.
Decode error &%Sx
(where x is the
incorrect character)
Invalid Convert to
Escape Character
Invalid decode mode
specified
Macro ID already in
use on SIMM. Print
menus to see a list
of used ID’s.
Macro size exceeds
available space
Non-hexadecimal
value received.
Non integer value
received.
Integer string
incorrect length
Non-integer value
received.
Password Length
Error.
Password Match
Error
Security Lock Not
Enabled Error.
Integer string
incorrect length.
Non-integer value
received.