Filter
Top Products
5 - Basic operations
34
TASCAM DA-78HR
5
Press the
CLEAR
(
PRE ROLL
) key once more
so that the d isplay shows
PO 0003 (
PO 0003
),
i.e. the post-roll time.
Since there is little point in setting pre- and post-roll
times to frame accuracy, you can only set these val-
ues to second accuracy.
The minimum values you can set are 5 seconds (pre-
roll) and 3 seconds (post-roll) and the maximum
value is 59 minutes 59 seconds for both.
Any punch operation from now will take your setting
for pre-roll and use it when locating the tape to the
punch-in point. For example, if your pre-roll time has
been set to 10 seconds (00:00:10.00), and the punch-
in point is at 00:06:03.12, the tape will locate to
00:05:53.12 when starting rehearsal or punch-in.
5.6.5 Rehearsing the punch-in
After you have set the punch points, and you have
located the tape to the pre-roll point, as described
above, you can rehearse the punch process.
1
Press the
RHSL
key so that the indicator lights
steadily.
This indicates that you are now in rehearsal
mode.
2
Press
PLAY
. The tape will start playing from
the pre-roll point.
3
At the punch-in point, monitoring will change
to source.
The
RECORD
key will flash, and the
REC
FUNCTION
indicator of any armed tracks will
light steadily. However, recording will not be
carried out.
4
At the punch-out point, monitoring will change
back to off-tape monitoring.
The tape will continue playing to the post-roll
point and then rewind to the pre-roll point.
5
Repeat the rehearsal process until you are sat-
isfied with the performance.
5.6.6 Interrupting a rehearsal or punch
recording
Very often while rehearsing a punch-in, you will not
want to run the tape all the way to the punch-out
point (an entry cue is missed, or a mistake is made
early on in the take). In these cases, the following
procedure applies to both rehearsal and punch
recording:
1
While the tape is running, press the
LOC 1
key
(there is no need to press
STOP
first).
The tape will return to the punch-in point,
minus the value specified in the punch-in offset
(5.6.4, “Editing the pre-roll and post-roll
tim es ”).
2
Pressing
PLAY
will then re-start the rehearsal
or punch-in process.
• Pressing the
LOC 2
key will locate the tape to the
punch-out position minus the punch-in pre-roll
time.
• These functions are only operative when the
RHSL
or
AUTO IN/OUT
indicators are lit or flashing.
When they are off, the
LOC 1
and
LOC 2
keys
will
act normally.
5.6.7 Recording the punch-in
1
Make sure the tape is at the pre-roll point, and
press the
AUTO IN/OUT
key once.
The indicator will flash, showing that the DA-
78HR is in auto-punch mode.
2
Press
PLAY
. The tape will start playing.
At the punch-in point, the
RECORD
indicator
will light steadily, as will the
REC FUNCTION
indicators of any armed tracks. Monitoring
will change from off-tape to source and the
IN PU T MONITOR
of any armed tracks will
light.
Recording will now actually take place. Any
recorded material which was previously on the
armed tracks between the punch points will be
replaced by the new recording.
3
At the punch-out point, the monitoring will go
back to off-tape (the
INPUT MONITOR
indica-
tors of armed tracks will go out), and when the
post-roll point is reached, the tape will rewind
to the pre-roll point.
4
The
AUTO IN/OUT
indicator will light steadily,
showing that the DA-78HR is now in replay
mode.
5.6.8 Replaying the punched material
1
To replay the punch-in, press the PLAY key.
Playback will start (the
REC FUNCTION
indi-
cators of the armed tracks will continue to
flash).
2
At the post-roll point, the tape will automati-
cally rewind to the pre-roll point.