Filter
Top Products
7 - Advanced operations
39
TASCAM DA-78HR
If you press
PLAY
twice while the tape is locating,
the
PLAY
key will light steadily, the tape will stop
and playback will start immediately.
If you are using the DA-78HR with a remote control
unit, and you have have pressed the
AUTO PLAY
key
on the remote control unit, replay will start automati-
cally when the location point is reached.
7.2 Repeat function
You can repeat playback continuously between the
two location memory points (Memo 1 and Memo 2).
NOTE
When we talk about the “first” and the “second” loca-
tions here, we are referring to the earlier and later
location times. Memo 1 could be at a later time than
Memo 2, and hence we would refer to it in this sec-
tion as the “second location point”.
The tape will wind to a little before the first point (if
it is not there already) and start playing. The off-tape
monitoring will start at the first memory location and
continue until the second location is reached. The
tape will then stop playing, and rewind to a little
before the first point and start playing again.
7.2.1 To start repeat play
1
When the two location points have been set,
press the
REPEAT
key.
2
The tape will locate to the first location point
and start playing until the second location
p oint, rewind to the fi rs t location point, an d
play again. This process will be repeated.
While the tape position is between the two
location points, the
REPEAT
indicator will be
lit steadily. It will flash while the tape position
is outside the two location points.
3
Stop the repeat function by pressing the
REPEAT
key (the
REPEAT
indicator will go
out).
If the tape is playing, it will continue playing
(past the second location point).
If the tape is rewinding to the first location
point when the
REPEAT
key is pressed, it will
stop.
NOTE
S
The two location points must be at least 5 seconds apart
for the repeat facility to be operational—if you attempt a
repeat operation when they are closer together than this,
the display shows
Too NEAR
(
TOO NEAR
).
If you have only set one location point, the repeat will be
between “00:00:00.00” and the location point.
Pressing any transport control while repeat pl ay is in
progress will stop the replay, but will not cancel the
repeat mode. To restart the repeat playback, locate
to either location point, and while the tape is winding,
press
PLAY
. Alternatively, press
PLAY
while the tape
is before the second location point.
7.3 Track delay
The DA-78HR allows you to delay tracks relative to
the other tracks, either when recording or playing
back. You can use this function for post-production
“slip”, compensate for delays caused by external pro-
cessing equipment, allow for propagation delay in
multi-microphone sessions or add special effects.
The track delay can be set from –200 samples to
+7200 samples. A negative number means that the
track on which the “delay” setting is made is
advanced in time relative to the other tracks. How-
ever, this does not mean that the DA-78HR includes a
time machine! Since the monitoring head is a “vir-
tual” head, made of a composite of delayed off-tape
and input source signals, the “position” of the record-
ing head can be adjusted in both directions.
1
Make sure that the unit is in shift mode (the
SHIFT
indicator is flashing).
2
Press the
RHSL
(
DELAY
) key.
3
The display can show the delay in samples or
milliseconds in which the delay is counted.
Press and release the
DELAY
key briefly in
order to change between these two units.
Millisecond delays are shown as 3-digit values,
and sample displays are shown as 4-digit val-
ues (always with leading zeroes).
4
Typically, all tracks will have their delay set
together (as shown by the display). Use the ▲
and ▼ keys to change the value.
You can also use the
DATA/LEVEL
knob to set
the delay value (see 4.3.7, “Using the DATA/
LEVEL knob to set values”).
5
Press a track’s
REC FUNCTION
key to s el ect an
individual track whose delay value can be
changed.
6
To change from editing individual track valu es
back to all tracks together, press and hold the
DELAY
key for more than one second.