Filter
Top Products
5
5. Installation
5.1 General Safety Instructions
• Read all of these instructions. Save them for future reference.
• Follow all warnings and instructions marked on the device.
• Donotplacethedeviceonanyunstablesurface(cart,stand,table,
etc.). If the device falls, serious damage will result.
• Donotusethedevicenearwater.
• Donotplacethedevicenear,orover,radiatorsorheatregisters.
• The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect
against overheating, these openings must never be blocked or
covered.
• The device should never be placed on a soft surface (bed, sofa,
rug, etc.) as this will block its ventilation openings. Likewise, the
device should not be placed in a built in enclosure unless adequate
ventilation has been provided.
• Never spill liquid of any kind on the device.
• Unplugthedevicefromthewalloutletbeforecleaning.Donotuse
liquid or aerosol cleaners. Use a damp cloth for cleaning.
• The device should be operated from the type of power source
indicated on the marking label. If you are not sure of the type of
power available, consult your dealer or local power company.
• This device is designed for IT power distribution systems with up to
230Vphase-to-phasevoltage.
• Thedeviceisequippedwitha3-wiregroundingtypeplug.Thisis
a safety feature. If you are unable to insert the plug into the outlet,
contactyourelectriciantoreplaceyourobsoleteoutlet.Donot
attempttodefeatthepurposeofthegrounding-typeplug.Always
follow your local/national wiring codes.
• Donotallowanythingtorestonthepowercordorcables.Routethe
power cord and cables so that they cannot be stepped on or tripped
over.
• If an extension cord is used with this device make sure that the total
of the ampere ratings of all products used on this cord does not
exceedtheextensioncordampererating.Makesurethatthetotalof
all products plugged into the wall outlet does not exceed 15 amperes.
• Consideration should be given to the connection of equipment to the
supply circuit, and what effect overloading the supply circuit might
have on overcurrent protection and supply wiring.
• To help protect your system from sudden, transient increases and
decreases in electrical power, use a Tripp Lite Surge Suppressor, Line
Conditioner or Uninterruptible Power Supply (UPS).
• Position system cables and power cables carefully; be sure that
nothing rests on any cables.
• Whenconnectingordisconnectingpowertohot-pluggablepower
supplies, observe the following guidelines:
• Install the power supply before connecting the power cable to the
power supply.
• Unplug the power cable before removing the power supply.
• If the system has multiple sources of power, disconnect power
from the system by unplugging all power cables from the power
supplies.
• Never push objects of any kind into or through cabinet slots. They
may touch dangerous voltage points or short out parts resulting in a
risk of fire or electrical shock.
• Donotattempttoservicethedeviceyourself.Referallservicingto
qualified service personnel.
• If the following conditions occur, unplug the device from the wall
outlet and bring it to qualified service personnel for repair:
• The power cord or plug has become damaged or frayed.
• Liquid has been spilled into the device.
• The device has been exposed to rain or water.
• The device has been dropped, or the cabinet has been damaged.
• The device exhibits a distinct change in performance, indicating a
need for service.
• The device does not operate normally when the operating
instructions are followed.
• Only adjust those controls that are covered in the operating
instructions. Improper adjustment of other controls may result in
damage that will require extensive work by a qualified technician to
repair.
• Use of this equipment in life support applications where failure
of this equipment can reasonably be expected to cause the failure
of the life support equipment or to significantly affect its safety or
effectivenessisnotrecommended.Donotusethisequipmentin
the presence of a flammable anesthetic mixture with air, oxygen or
nitrous oxide.
Rack Mounting Safety Instructions
• The ambient operating temperature in the rack may be an issue and
is dependent upon the rack load and ventilation. When installing in
aclosedormulti-unitrackassembly,makesurethatthetemperature
will not exceed the maximum rated ambient temperature.
• Before working on the rack, make sure that the stabilizers are secured
to the rack, extended to the floor, and that the full weight of the rack
rests on the floor. Install front and side stabilizers on a single rack or
front stabilizers for joined multiple racks before working on the rack.
• Always load the rack from the bottom up, and load the heaviest item
in the rack first.
• Always load the rack so that a hazardous condition is not created due
to uneven loading.
• Makesurethattherackislevelandstablebeforeextendingadevice
from the rack.
• Use caution when pressing the device rail release latches and sliding
a device into or out of a rack; the slide rails can pinch your fingers.
• After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
• DonotoverloadtheACsupplybranchcircuitthatprovidespower
totherack.Thetotalrackloadshouldnotexceed80%ofthebranch
circuit rating.
• Ensure that proper airflow is provided to devices in the rack.
• Donotsteponorstandonanydevicewhenservicingotherdevices
in a rack.
• DonotconnecttheRJ11connectormarked“Upgrade”toapublic
telecommunication network.
• Caution!Slide/Rail(LCDKVM)mountedequipmentisnottobe
used as a shelf or a work space.
CAUTION!
Slide/rail-mounted
equipment is not to be
used as a shelf
or a workspace.