Filter
Top Products
Index
Index-1
Numerics
2-port error corrections,
performing
, 6-42, 6-71
4 Param Displays softkey
, 1-18
A
aborting a print or plot process
,
4-33
absolute
ripple test value
, 1-88, 1-89
absolute power
, 6-39
accuracy enhancement
, 7-7, 7-37,
7-51
accurate measurements of
electrically long devices
cause of measurement
problems
, 5-8
improving measurement
results
, 5-8
activating
averaging
, 5-16
chop sweep mode
, 5-13
display markers
, 1-25
fixed markers
, 1-29
limit test
, 1-79
activating the bandwidth test
,
1-95
active channel display
, 1-11
adapter removal
, 6-41
adapter removal calibration
(ECal)
, 6-69–6-75
adapters
minimizing error
, 6-47
adapters, matched
, 6-45
ADC
, 7-6
address menu
, 7-80
addressing two sources
, 2-30
adjusting
display colors
, 1-22
relative velocity factor
, 3-12
AmiPro, using
, 4-23
amplifiers, measuring
, 1-52
amplitude tracking
, 2-39
amplitude, tracking
, 1-41
analog in menu
, 7-22
analyzer display formats
, 7-24
group delay format
, 7-25
group delay principles
, 7-29
imaginary format
, 7-29
linear magnitude format
, 7-27
log magnitude format
, 7-24
phase format
, 7-24
polar format
, 7-27
real format
, 7-29
smith chart format
, 7-26
SWR format
, 7-28
analyzer internal memory, what
you can save
, 4-36
applying power
, 8-5
arrays
format
, 7-8
pre-raw data
, 7-7
raw
, 7-7
ASCII data formats
, 4-41
CITIfile
, 4-41
S2P data format
, 4-42
assigning standards to various
TRL classes
, 6-51
assigning standards to various
TRM classes
, 6-55
attenuator
, 7-13
attenuator settings, selecting
,
1-61
attenuator, repetitive switching
,
7-13
attenuator, source step
, 7-4
auto sweep time mode
, 7-11
auto sweep time mode, setting
,
5-12
auto-feed, selecting
, 4-15
automatic mode
, 7-9
autostarting sequences
, 1-106
averaging
, 7-34
isolation
, 6-61
averaging factor, reducing
, 5-12
averaging, activating
, 5-16
averaging, sweep to sweep
, 7-6
B
band
adding a frequency
, 1-85
changing a frequency
, 1-84
deleting a frequency
, 1-86
frequency
, 1-83
bandwidth
, 1-94
bandwidth markers
displaying
, 1-95
bandwidth test
activating
, 1-95
running
, 1-94–1-97
setting up limits
, 1-92–1-94
bandwidth testing
, 1-92–1-97
bandwidth value
displaying
, 1-96
bandwidth, searching for
, 1-41
basic measurements, making
, 1-4
bilateral device
, 6-22, 6-25
blanking the display
, 1-21
block, receiver
, 7-4
built-in synthesized source
, 7-3
source step attenuator
, 7-4
built-in test set
, 7-4
C
cables, interconnecting
, 5-4
calculating statistics of
measurement data
, 1-42
calculations, ratio
, 7-6
calibrating for non-coaxial
devices
, 6-50
TRL error-correction
, 6-50
TRM error correction
, 6-54
calibrating for noninsertable
devices
, 6-40
adapter removal
, 6-41, 6-69
matched adapters
, 6-45
modifying the cal kit through
definition
, 6-46
calibrating the analyzer receiver
to measure absolute power
,
6-39
calibration
ECal
, 6-58–6-68
electronic. See ECal
power meter
, 2-12
calibration considerations
, 6-4
calibration standards
, 6-5
clarifying type-N connector sex
,
6-4
device measurements
, 6-4
error-correction stimulus state
,
6-9
frequency response of
calibration standards
, 6-6
interpolated error correction
,
6-8
measurement parameters
, 6-4
omitting isolation calibration
,
6-4
restarting a calibration
, 6-5
saving calibration data
, 6-5
calibration data, saving
, 6-5, 7-65
calibration kit menu
, 7-58
defining standard menus
, 7-59
label class menu
, 7-65
label kit menu
, 7-65
label standard menu
, 7-62
specify class menu
, 7-62
specifying offset menu
, 7-61
calibration kit, saving a modified
,
7-65
calibration kits, modifying
, 7-57
calibration routines
, 7-54
full two-port calibration
, 7-55
response and isolation
calibration
, 7-54
response calibration
, 7-54
S11 and S22 one-port
calibration
, 7-55