Filter
Top Products
FS-8700-47 DNP 3.0 Driver Manual Page 49 of 51
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com
Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com
Error Message Explanation
DNP3:#60 Msg Frame
abandoned. Frames out of seq.
Exp=%d Rcvd=%d. TP=%#d
Some DNP messages contain too much data to be sent in one
message. Such messages are split into multiple frames and
reassembled on the receiving side. Each frame has a sequence
number. If frames are received out of sequence this message is
printed. Typically, once one frame is found out of sequence the
remaining frames may be flagged as errors too. A consequence of
this message is the loss of the complete message. If this message
is printed rarely, you could assume that it is a consequence of
occasional corruption. If it is printed often then take a log and call
Tech support.
DNP3:#61 FYI. Read func
changed Now=%s. MD=<%s>
When the DNPfunction parameter is omitted on a Map Descriptor
used to read data the driver assumes that the intended
DNPfunction is ‘read’. However in some case the driver knows that
for certain Objects the function must be changed and does this
automatically. This message gives a heads. No action is required
from you.
DNP3:#62 Err. Rejected msg with
multiple polls.
The Server side of the driver can only process messages which poll
for one class of data at a time. Re-configure your Client and try
again. This message is obsolete. Only driver version 1.03i and
older produce the message. Read Appendix A.20 for more info.
DNP3:#64 Err. To serve class
data set the DNPAssoc value
non-zero
To serve class data the parameter dnpAssociate must be specified
on all associated Map Descriptors and the value of the parameter
must be non-zero.
9
DNP3:#65 Err. There are no MD
associated with the class MD=%s
Refer to Section 5.3.5.
9
DNP3:#63a Err. Cant open %s for
poll from log
DNP3:#63b Err. Cant read 1st
line of %s
DNP3:#63c FYI. Sending
message from log file=%s
If any of these messages are printed call tech support. An internal
diagnostic specific to QA testing has been activated. It is possible
for the driver to send a message that is found in a log file instead of
the configured poll to test the Server side of the driver. Script S4085
provides an example. The Client side MD name must have '.log in
the name and the driver opens that file and sends the 1st line (only)
as a single message. The line is expected to have hex bytes
delimited by space or square brackets.
DNP3:#66 Err. Index Style=%d
not supported.
The Server side of the driver does not support the indicated
index_style. Refer to Appendix A.17. Reconfigure your Client to
use a different qualifier and try again
9
DNP3:#67 FYI Serve 'changed'
data only. Class=%d
This message confirms that the Server has been configured to
serve ‘changed’ data only. Thus, only data whose value has
changed by some dead band since the last poll for class data will
be served. You can safely ignore this message if it confirms your
expectations. If not then review your configuration.
DNP3:#68 FYI. Class Data
Served with Qualifier=%#x
When the Server serves class data and when configured to serve
only ‘changed’ data then the Server may change the qualifier of the
response from the default or configured qualifier because the points
being served in the response may not be sequential. You may
ignore this message as it does not report an error. It is printed to
draw your attention to the fact that the master should be configured
to receive a response that uses a different qualifier.
DNP3:#69 FYI. Server signals
Client=%d to time synch
Each time that the Server sets the internal indication bit to signal
the master station that a time update is required this message is
printed. You can safely ignore it if it confirms your expectations.
Refer to Appendix A.18.
9
Edit the CSV file, download to the FieldServer and reset the FieldServer.