JVC DLA-G150HTE Projector User Manual


 
DLA-G150HTE
1-26
No.51847
48
Menu Operations
Adjusting Picture Quality
In the Image adj. submenu, adjust brightness, contrast, sharpness, etc. to obtain the desired picture quality. Note that the
adjustment items differ in Video menu mode and PC menu mode.
1
Press the MENU button.
The main menu appears on the screen.
2
Select “Image adj.” with the cursor button 5
55
5 or
, and press 3
33
3 or the ENTER button.
The Image adj. submenu appears on the screen.
Video submenu PC submenu
3
Select the item to be adjusted with the cursor button 5
55
5 or
.
*“Color” and “Tint” are shown in Video submenu only.
4
Make adjustment with the cursor 2
22
2 or 3
33
3.
*To adjust multiple items, repeat 3 and 4.
* : Factory set value
To perform All Reset
In the Image adj. submenu, select All reset with the cursor button 5 or , and press the ENTER button. Then, the All
reset submenu appears on the screen.
Press the cursor button 2 to select Yes, and then press the ENTER button.
All items in the Image adj. submenu are reset to the factory set values and the menu returns to the previous one.
To exit the All reset submenu without performing All reset, select No with the cursor button 3 and, press the ENTER
button.
(To be continued on the next page)
Image adj.
Brightness
Contrast
Sharpness
Color
Tint
All reset
12
12
1
12
12
ENTER
Image adj.
Brightness
Contrast
Sharpness
All reset
12
12
ENTER
1 2 3 4 5
Adjustment item Button Adjustment content
Brightness
2
or
3
Gets darker/brighter. (30
0*
+30)
Contrast
2
or
3
Gets lower/higher. (30
0*
+30)
Sharpness
2
or
3
Gets softer/sharper.
Video menu mode: (5 0* +5)
PC menu mode: (1
3*
5)
Note
When in the PC menu mode, if the resize function in the PC submenu is set to
1:1, the image quality will not change even if the value is changed.
Color
2
or
3
Gets softer/deeper. (30 0* +30)
(Video menu mode only)
Tint 2 or 3
Gets reddish/greenish. (30 0* +30)
(Video menu mode only)
All reset ENTER
Resets above items to the factory set values. How to operate is mentioned below
(next page).
47
Menu Operations
ENGLISHDEUTSHFRANÇAISITALIANOESPAÑOL
Setting for Watching Image Software (Video Menu Mode Only)
This unit has a function which allows you to project movies, which were recorded on film, in the best possible conditions.
(Function to convert 2-3 pull-down interlace scans to progressive scans)
Normally use set to AUTO.
1
Press the MENU button.
The main menu appears on the screen.
2
Select “Setting” with the cursor button 5 or , and press 3 or the ENTER button.
The Setting 1 submenu appears on the screen.
3
Select “Setting 2” with the cursor button 5 or , and press 3 or the ENTER button.
The Setting 2 submenu appears on the screen.
4
Select “Film” with the cursor button 5 or .
5
Select the Film function mode with the cursor button 2 or 3.
OFF: When watching images recorded with a video camera
ON: When watching images recorded on film
AUTO: The setting is changed automatically
6
Press the EXIT button to return to the previous menu or press the MENU button to
exit the menu mode.
Note
Operates when the signal is an NTSC or PAL interlace signal. Does not operate for other signals. (The menu is not
displayed when other signals are inputted.)