Filter
Top Products
CC100Master Bridge User’s Guide
40
dconfig
Dump all configurations/settings.
default
Reset all settings to factory default, except Password.
diag
-t <mac>
-r <mac>
On-line EP connection diagnosis.
-t: downstream SNR diagnosis(from Master to EP)
-r: upstream SNR diagnosis(from EP to Master)
<mac>: EP MAC <mac> to be diagnosed
dir
Show detail file information resides in flash ROM. Include
‘Working Area’ and ‘Upload Area’, refer
Figure 4. The listed
filenames are,
‘bootcode’: boot loader
‘sysfw4m’: system firmware
‘G1C28H21M’: Master HCNA driver
‘G0C28H20Ep’: 3010 EP HCNA driver
‘G1C28H21Ep’: 3110 EP HCNA driver
‘diagsw’: 3010 diagnosis utility file
‘diagsw1’: 3110 diagnosis utility file
Accompanying with file id, file version, file date, and file size.
dns
[-s <pri/sec> <ip>] Display or set up DNS server setting.
-s pri <ip>: set up Primary DNS server’s IP
-s sec <ip>: set up Secondary DNS server’s IP
exit
Close the Telnet console.
quit
Close the Telnet console.
ep
[-c <hostcnt>]
[-n <note>]
[-u <uprate index>]
<mac>
Set up the EP
Properties Profile related setting values.
<hostcnt>: EP Host Limit setting value (0~255), default 255
<note>: EP Note setting value
<uprate index>: EP
Upstream Rate setting value ( 0~1563,
*64Kbps), default 0 for unlimited
<mac>: designated EP MAC to configure
ephpnareboot
(Smart EP)
-m <mac> Reset remote Smart EP device
epstat
(Smart EP)
-m <mac>
[-r]
Display remote Smart EP port statistics for port
LAN1/LAN2/HCNA.
-r: reset all port statistics counter to 0
epswc
(Smart EP)
-m <mac>
[-t]
[-u]
[-r]
[-d]
[-p <lan1/lan2/hpna>
[-l <up/down>]
[-s <auto /10h /10f
/100h /100f>]
[-f <on/off>]]
Display or set up remote Smart EP built-in switch Ethernet
properties
-t: display EP switch settings
-u: display EP switch/port status
-r: reset EP switch
-d: reset EP switch’s eeprom settings to factory default
-p: configure EP port LAN1/LAN2/HCNA
-l: link, <up/down>: force current port to link up or down, i.e.
enable/disable current port
-s: current port Ethernet mode setting,
<auto>: auto-negotiation mode
<10h/10f/100h/100f>: 10/100Mbps, half/full-duplex mode
-f: current port Ethernet flow-control setting,
<on/off>: turn on /off flow control
epswigmp
epswqosq
epswqosrate
epswqostc
epswtagvlan
(Smart EP)
-m <mac> Refer swigmp, swqosq, swqosrate, swqostc, swtagvlan for the
same functionality, but operate on remote Smart EP with
designated MAC address <mac>
filter
[-s <set>
[-c <act/deact>]
[-a <ip> -m <mask>]
[-t <allow/deny>]
[-w <allow/deny>]
Display or set up the filter rule set, refer the section “
Allow
Source” for IP <ip> and Subnet Mask setup <mask>.
<set>: filter set index, total 16 set (0~15)
<act/deact>: activate or de-activate the rule set
<allow/deny>: allow or deny the protocol