Filter
Top Products
ENGLISH-43
Adjustments and settings
42-ENGLISH
RESIZING
This should normally be set to “ON”.
(This setting is only for signals
which have lower resolutions than
the LCD panels. Refer to page 62
for details.)
ON
The pixel resolution of the input
signal is converted to the same
resolution as the LCD panels before
being projected. For signals with
lower resolutions, gaps in the pixels
are automatically interpolated into
the picture before it is projected.
This may sometimes cause
problems with the quality of the
picture.
OFF
The picture signal is projected at its
original resolution, with no pixel
conversion. The projected picture
will be smaller than normal, so
adjust the zoom setting or move the
projector forwards or backwards to
adjust the picture size if necessary.
If set to “OFF”, some features, such
as D.ZOOM (digital zoom) or
keystone distortion correction will
not function.
AUTO SETUP
This item functions in the same way
as the AUTO SETUP button on the
remote control unit. (page 27)
FRAME LOCK
If the picture’s condition is bad while
a RGB moving picture signal is
projected, set the FRAME LOCK to
“ON”. Refer to page 62 on
compatible RGB signals.
possible.
B
The picture size will also change when
correction of keystone distortion is
carried out.
B
The range of keystone correction varies
depending on the type of signal being
input (including when no signal is being
input). If you make an adjustment that is
outside the allowable range, the setting
will not be changed. In addition, if the
input signal changes after keystone
correction has been carried out, the
correction setting may be cancelled.
This indicates that the current correction
setting exceeds the allowable range for
the new input signal.
B
If you correct both vertical and horizontal
keystone distortion at the same time, the
allowable range of keystone correction
becomes smaller. If you make an
adjustment that is outside the allowable
range, the setting will not be changed.
B
The ratio of length and width of an
image may become incorrect depending
on the amount of the keystone
correction.
ratio is changed automatically to
project a 16:9 picture.
4:3
The input signal is projected without
change.
16:9
The picture is compressed to a ratio
of 16:9 and projected.
S4:3
The size of the input signal is
compressed to 75% and projected.
(This is useful for projecting a picture with
a 4:3 aspect ratio onto a 16:9 screen.)
OSD POSITION
Press the I or H buttons to move
the OSD position.
ASPECT
This setting is only valid for an S-
VIDEO/VIDEO signal and a YP
BPR
signal in 525i (480i), 525p (480p)
and 625i format.
AUTO
(S-VIDEO only)
When an S1 video signal is input to
the S-VIDEO terminal, the aspect
When a
squeezed
signal is being
input. (The
projected
image is
contracted
vertically)
[
S1 video signals
B
S1 video signals are a type of
video signal with an aspect ratio
of 16:9 which include a detector
signal. This detector signal is
output by some sources such as
wide-vision video decks. If the
AUTO setting above is selected,
this projector will recognise the
detector signal and automatically
switch the aspect ratio to 16:9 in
order to project the picture.
NOTE:
B
This projector is equipped with an
aspect ratio selection function.
However, if a mode which does
not match the aspect ratio of the
input signal is selected, it may
affect the quality of viewing of the
original picture. Keep this in mind
when selecting the aspect ratio.
B
If using this projector in places
such as cafes or hotels with the
aim of displaying programmes for
viewing for a commercial purpose
or for public presentation, note
that if the aspect ratio (16:9)
selection function is used to
change the aspect ratio of the
screen picture, you may be
infringing the rights of the original
copyright owner for that
programme under copyright
protection laws.
B
If a normal (4:3) picture which was
not originally intended for wide-
screen viewing is projected onto a
wide screen, distortion may occur
around the edges of the picture so
that part of the picture is no longer
visible. Such programmes should
be viewed in 4:3 mode to give
proper consideration to the aims
and intentions of the original
programme’s creator.
AUTO
4:3
16:9
S4:3
When using the 16:9 screen
When a 4:3
signal is being
input
[