Filter
Top Products
GT Stereo Input Module
The GT Stereo Input Module is essentially two GT Input
Modules fit into one module space. This module is very use-
ful for accepting remote feeds, effects inputs and other sig-
nals that require stereo handling.
48V Phantom Power Switch
Turns on 48V Phantom Power for both L and R XLR inputs,
required by certain microphones for proper operation.
LINE Switch
Selects between the Balanced XLR Microphone Input con-
nector and the Balanced Line Input 1/4" TRS connector for
both L and R channels.
XLR PAD Switch
Introduces a -20 dB drop to the mic input signal for both L
and R XLR inputs.
L GAIN & R GAIN Controls
Adjusts input gain for proper signal level for both L and R
inputs.
80Hz High Pass Switch
For both input channels, reduces all low frequency content at
a 12db per octave rate referenced to 80Hz (-3db point).
Polarity Reverse Switch
For both input channels, inverts the polarity of both the
microphone and line inputs. An internal jumper selects
between Left channel only or both Left & Right channels.
Three-Band Equalizer Controls
The equalization controls in this module act upon both L and
R stereo channels at once. The upper band is a fixed shelving
EQ with one control knob. The middle and low frequency EQ
bands are set up as sweep EQ’s: the lower knob controls the
gain or cut as in the fixed EQ; while the upper knob controls
the center frequency adjusted by the inner knob. These center
frequencies are printed on the chassis around the upper knob.
EQ IN Switch
Inserts the EQ section into both L and R input channel sig-
nals at once. An associated LED illuminates when the switch
is down.
AUX Level 1•3 / 2•4
Adjusts audio level of a mix for use as a monitor or an effect
send. The signal source for this mix may be selected pre or
post fader by an associated switch. The left channel is sent to
the odd Auxes, and the right channel is sent to the even
Auxes.
POST/PRE Switch
Selects the Aux 1•3 and Aux 2•4 signal sources between post
and pre fader positions.
STEREO Switch
AUX 5-8 Individual Level Controls normally send a summed
(L+R) signal to the AUX outputs. When the STEREO switch
is depressed, AUX 5 and 6 become a ‘right’ send and ‘left’
send respectively. This can be used for a stereo effects send.
SP / TC / GT
PAGE 14
CENTURY SERIES
+48V
LINE
80
EQ IN
STEREO
POST
5
6
7
8
XLR
PAD
1•3
2•4
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
Ø
WID
REV
STR
MONO
16 16
88
O+
16 16
88
O+
HF
LF
100
40
150
300
6
1K
600
300
1K
3
5
8K
3
1K
5
10
15
20K
16 16
88
O+
MID
GAIN
20
10
6
30
60
20
10
6
30
60
STEREO
POST
MUTE
MONO
1-2
3-4
5-6
7-8
PFL
SCENE
MUTE
SELECT
A
B
C
D
PEAK
SIG
5
6
7
8
SAFE
0
5
10
30
40
20
L-R
1•3
2•4
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
7
8
9
5
2
0
1
3
46
10
1
BAL
WID
REV
STR
MONO