Filter
Top Products
TAPE MANAGEMENT FUNCTION
This VCR is equipped with a tape management function.
Using this function you can protect previous recordings
and prevent overuse of the tape by controlling the tape
protection term (number of days), the maximum number
of re-recordings of the tape and the recording group. To
use the tape management function, it must be set before
recording is started. The tape management data is
recorded at the beginning of the tape. For details on how
to set this function, refer to “Setting the Tape
Management Function”.
PROTECT DAY: To set the number of days before the
tape can be rerecorded over.
REC PASS SET: To limit the number of rerecordings, in
order to maintain a good image quality.
GROUP NO.: To manage tapes belonging to different
recording groups.
NOTE:
•
Before using this function, make sure that the clock is
set properly.
Operation
When recording is started, the VCR will rewind the tape to
the beginning, and will playback some of the tape to
check for the presence of tape management data (no
image is displayed). While the presence and type of data
are checked, the message “T. MANAGE. CHK” is
displayed on-screen.
NOTES:
•
When a program timer recording is set, the tape
management data is checked after the TIMER button is
pressed to complete the program timer recording
setting.
•
During alarm recording, the tape management function
will not operate even if it is active.
If no tape management data is present on the
tape
Recording will start according to the settings in the
(TAPE MANAGEMENT) menu.
When recording starts, the updated tape
management data is recorded onto the tape.
If the tape has already been recorded on, the
message “USED TAPE” will flash on-screen until
recording starts.
If tape management data is present on the tape
The tape management data is checked and if there is
no conflict, the VCR will rewind the tape to the
beginning, then recording starts and the updated tape
management data is recorded onto the tape. While the
tape is rewound and the tape management data
recorded, the message “T. MANAGE. OK” is displayed
on-screen.
If a conflict is found when the tape management data is
checked, the (TAPE MANAGEMENT) menu is displayed
and the conflicting setting will flash. This menu will show
the settings taken from the data recorded on the tape and
not the current data settings held in the VCR’s (TAPE
MANAGEMENT) menu setting. Refer to “Tape
Management Conflict Display” for detailed information.
NOTES:
•
During Autorepeat recording, the tape management
data at the beginning of the tape will be checked and
updated every time the tape is rewound to the
beginning. However, the “PROTECT DAY” setting will
be ignored. Also, even if there is a conflict with the
“REC PASS SET” number, autorepeat recording will
continue without any warning.
•
If the VCR is set for alarm recordings, alarm recording
will be done based on the different settings.
If an alarm trigger is received while the tape is being
first rewound, the tape will continue to be rewound to
the beginning, then alarm recording will be done after
the tape has been advanced of a preset duration.
If an alarm trigger is received while the message “T.
MANAGE. CHK” is displayed on-screen, in order to
prevent erasing the tape management data recorded at
the beginning of the tape, the tape is advanced of a
preset duration, then alarm recording starts.
If an alarm trigger is received while tape management
data is being recorded onto the tape, alarm recording
will only start after all the data has been recorded.
Furthermore, when setting a program timer recording,
in order to protect the data, no alarm trigger will be
received until the first program timer recording starts.
IMPORTANT NOTES:
•
If the tape management data cannot be read, the
VCR will switch to stop mode and “INCORRECT
DATA” will be displayed on-screen.
This may indicate that the beginning of the tape
(data recording/reading section) is damaged and
the tape may be unusable.
The message “INCORRECT DATA” will disappear
when the EJECT, STOP or PLAY button is pressed.
•
Set the security lock function to on in order to
protect the security of this feature.
NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001
16
English