Filter
Top Products
TAPE MANAGEMENT FUNCTION
Setting the Tape Management Function
1
Press the MENU button until the (TAPE
MANAGEMENT) menu is displayed.
@@@@<TAPE@MANAGEMENT>
*TAPE@MANAGE.@@@@N
*PROTECT@DAY@@@@@30
*REC@PASS@SET@@@@10
*GROUP@NO.@@@@@@@OFF
*OVERRIDE@@@@@@@@N
2 Press the l (or j) button to select the desired mode.
N . . . . . . The tape management function is not
active.
Y. . . . . . . The tape management function is active.
When setting to “Y”, please continue with the settings
below.
3 Press the ] button, until the “PROTECT DAY” setting
is flashing.
4
Press the l (or j) button to select the desired
number of days to protect the tape.
OFF . . . . The tape is not protected.
1-255 . . . Number of days to protect the tape
(prevent over-recording), from the date
of the last recording on the tape (or the
last expected recording date (calculated
using the tape length (T-120 or T-160)
and the recording speed).
NOTES:
•
Since the last expected recording date is a
calculated date (using the tape length (T-120 or
T-160) and the recording speed), it may be different
from the actual last recording date, this due to other
settings such as (alarm recordings, program timer
recordings, holiday settings).
•
When setting a program timer recording, the tape
protection term is checked when the VCR is set to
program timer recording stand-by mode.
•
When a program timer recording is done, the data
is updated when recording starts. Even if the
recording is stopped before the programmed time,
the original data (last expected recording date) will
remain as calculated.
5
Press the ] button, until the “REC PASS SET” setting
is flashing.
6
Press the l (or j) button, to select the desired
number of re-recording times.
OFF . . . . The number of re-recording times will not
be checked.
1-100 . . . Maximum number of re-recording times.
(Refer to “Concerning the Number of Times Tapes
can be Rerecorded on” on page 20.)
NOTES:
•
The data is updated at the beginning of the
recording. Even if the recording is stopped before
the end, the original data information will be
considered.
•
During Autorepeat recording, the re-recording times
count will be updated every time the tape is
rewound to the beginning. Autorepeat recording will
proceed even if the count exceeds the “REC PASS
SET” setting. If in the BUZZER section WARNING
is set to “Y”, the buzzer is heard.
7
Press the ] button, until the “GROUP NO.” setting is
flashing.
8
Press the l (or j) button, to select the desired group
number.
OFF . . . . The group number will not be checked.
1-15 . . . . Group number setting.
9
Press the ] button, until the “OVERRIDE” setting is
flashing.
F
Press the l (or j) button, to select the desired
override mode.
Y. . . . . . . In case of a conflict that prevents
recording, the next operation is
executed. If recording is done, then the
last recording date and the re-recording
times count are updated.
N. . . . . . . In case of a conflict that prevents
recording, the (TAPE MANAGEMENT)
menu is displayed and the conflicting
setting preventing recording will flash.
The only possible action is to press the
EJECT button, in order to eject the tape.
(Refer to “Tape Management Conflict
Display”.)
G
Press the PAUSE/SEARCH button to save the
settings.
NOTES:
•
Once the tape management data is recorded on
tape, it cannot be changed.
•
The criteria (condition) for allowing recording will be
based on the data recorded on the tape and not the
settings in the (TAPE MANAGEMENT) menu.
NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001
English
17