Filter
Top Products
50 Specifications
VD:
Vertical sync input: 1-5 Vp-p
high impedance, positive/
negative
INPUT B Digital RGB: DVI-D (TM-DS)
INPUT C Analog RGB/component: 5BNC
(female)
R/R-Y: 0.7 Vp-p ±2 dB
(75 ohms terminated)
G: 0.7 Vp-p ±2 dB (75 ohms
terminated)
G with sync/Y: 1 Vp-p ±2 dB
sync negative (75 ohms
terminated)
B/B-Y: 0.7 Vp-p ±2 dB (75
ohms terminated)
SYNC/HD:
Composite sync input: 1-5 Vp-p
high impedance, positive/
negative
Horizontal sync input: 1-5 Vp-p
high impedance, positive/
negative
VD:
Vertical sync input: 1-5 Vp-p
high impedance, positive/
negative
MONITOR OUT
HD D-sub 15-pin (female)
R, G, B: Gain Unity: 75 ohms
SYNC/HD,VD: 4 Vp-p (open),
1 Vp-p (75 ohms)
*DIGITAL RGB signal is not
output from MONITOR OUT
terminal.
TRIG Minijack
Power on: 12 V DC, output
impedance: 4.7 kilohms
Power off: 0 V
RS-232C D-sub 9 pin (female)
CONTROL S IN/PLUG IN
POWER Stereo minijack, 5 Vp-p, plug-in
power 5 V DC
NETWORK RJ-45: 10BASE-T/100BASE-TX
General
Dimensions VPL-FX52: 480 × 169 × 502 mm
(19 × 6
5
/8 × 19
7
/8 inches)
(w/h/d) (with the projection
parts)
VPL-FX52L: 480 × 169 × 464 mm
(19 × 6
5
/8 ×18
3
/8 inches)
(w/h/d) (with the projection
parts)
Mass VPL-FX52: Approx. 10.5 kg (23
lb 4 oz)
VPL-FX52L: Approx. 9.1 kg (20
lb 1 oz)
Power requirements
AC 100 to 240 V, 4.0 A - 1.6 A,
50/60 Hz
Power consumption
Max. 400 W
in standby mode: 7 W (when
network function is operating)
Heat dissipation
1,365 BTU
Operating temperature
0°C to 35°C (32°F to 95°F)
Operating humidity
35% to 85% (no condensation)
Storage temperature
–20°C to 60°C (–4°F to 140°F)
Storage humidity
10% to 90%
Supplied accessories
Remote Commander (1)
Size AA (R6) batteries (2)
Lens cap (1) (for VPL-FX52 with
standard lens only)
AC power cord (1)
Air filter (for replacement) (1)
Operating Instructions,
Installation Manual for Dealers
(CD-ROM) (1)
Quick Reference Manual (1)
Safety Regulations (1)
Security Label (1)
Warranty Card (1)
Design and specifications are subject to change
without notice.
Always verify that the unit is operating
properly before use. SONY WILL NOT BE
LIABLE FOR DAMAGES OF ANY KIND
INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT
ON ACCOUNT OF THE LOSS OF
PRESENT OR PROSPECTIVE PROFITS
DUE TO FAILURE OF THIS UNIT, EITHER
DURING THE WARRANTY PERIOD OR
AFTER EXPIRATION OF THE
WARRANTY, OR FOR ANY OTHER
REASON WHATSOEVER.
Optional accessories
Projector Lamp
LMP-F300
(for replacement)
Projector Suspension Support
PSS-620
Signal Interface Cable
Note