Filter
Top Products
TABLE OF CONTENTS
3.8.8 Address se
t
ting……………….……………………………………………………………..
Pg. 18
3.8.9 Baud rate se
t
ting…………………………………………………………………………….
Pg. 18
3.9 CONNECTING THE LOAD………………………………………………………………………..
Pg. 19
3.9.1 Load Wi
r
ing…………………………………………………………………………………..
Pg
. 19
3.9.2 Current Carrying Capa
c
ity………………………………………………………………….
Pg. 19
3.9.3 Wire termination…………………………………………………………………………….
Pg. 20
3.9.4 Noise and Impedance E
f
fects……………………………………………………………...
Pg. 20
3.9.5 Inductive loads………………
……………………………………………………………….
Pg. 20
3.9.6 Making the load conne
c
tions……………………………………………………………….
Pg. 21
3.9.7 Connecting single loads, local sensing (d
e
fault)…………………………………………
Pg. 24
3.9.8 Connecting single loads, remote sen
s
ing…………………………
……………………...
Pg. 24
3.9.9 Connecting multiple loads, radial distribution method…………...……………………...
Pg. 24
3.9.10 Multiple loads connection with distribution term
i
nals…………………………………..
Pg. 25
3.9.11 Grounding ou
t
puts………………………………………………………
…………………
Pg. 25
3.10 LOCAL AND REMOTE SENSING………………………………………………………………
Pg. 26
3.10.1 Sensing wi
r
ing……………………………………………………………………………...
Pg. 26
3.10.2 Local sen
s
ing……………………………………………………………………………….
Pg. 26
3.10.3 Remote sen
s
ing……………………………………
………………………………………
Pg. 27
3.10.4 J2 sense connector technical inform
a
tion………………………………………………
Pg. 27
3.11 REPACKAGING FOR SHIPMENT………………………………………………………………
Pg. 27
CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS
………………...
Pg. 28
4.1 INTRODUCT
ION……………………………………………………………………………………
Pg. 28
4.2 FRONT PANEL
CONTROLS AND INDICATORS…………………………………………….
Pg. 28
4.3 REAR PANEL
CONNECTIONS AND CONTROLS…………………………………………..
Pg. 30
4.4 REAR PANEL SW1 SETUP SWITCH……………………………………………………………
Pg. 31
4.4.1 SW1
positions fun
c
tions……………………………………………………………………
Pg. 32
4.4.2 Resetting the switch…………………………………………………………………………
Pg. 32
4.5 REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR……………………
Pg. 33
4.5.1 Making J1 conne
c
tions…………………………………………………………………….
.
Pg. 33
CHAPTER 5 LOCAL OPERATION
………………………………………………………………….
Pg. 35
5.1 INTRODUCTION…………………………………………………………………………………..
Pg. 35
5.2 STANDARD OPERATION…………………………………………………………………………
Pg. 35
5.2.1 Constant Voltage Mode…………………………………………………………………….
Pg.
35
5.2.2 Constant Current Oper
a
tion………………………………………………………………..
Pg. 35
5.2.3 Automatic Cros
s
over………………………………………………………………………..
Pg. 36
5.3 OVER VOLTAGE PROTECTION (OVP)………………………………………………………...
Pg. 36
5.3.1 Setting the OVP level…………………
…………………………………………………….
Pg. 36
5.3.2 Activated OVP protection indic
a
tions……………………………………………………..
Pg. 36
5.3.3 Resetting the OVP ci
r
cuit…………….. …………………………………………………...
Pg. 36
5.4 UNDER VOLTAGE LIMIT……………………………………………………………………….. .
Pg. 37
5.4.1 Setting the UVL level………………………………………………………………………..
Pg. 37
5.5 FOLDBACK PROTECTION……………………………………………………………………….
Pg. 37
5.5.1 Setting the Foldback prote
c
tion…………………………………………………………….
Pg. 37
5.5.2 Resetting activated Foldback prote
c
tion………
…………………………………………..
Pg. 37
5.6 OUTPUT ON/OFF CONTROL…………………………………………………………………….
Pg. 37
5.7 OUTPUT SHUT
-
OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR………………
Pg. 37
5.8 ENABLE/DISABLE CONTROL VIA………………………………………………………………
Pg. 38
5.9 CV/CC SIGNAL……………………………………
………………………………………………..
Pg. 38
5.10 PS OK SIGNAL……………………………………………………………………………………
Pg. 38
5.11 SAFE START AND AUTO
-
RESTART MODES………………………………………………..
Pg. 39
5.11.1 Automatic start mode………………………………………………………………………
Pg. 39
5.11.2 Safe start mode……………
………………………………………………………………..
Pg. 39
5.12 OVER TEMPERATURE PROTECTION (OTP)………………………………………………..
Pg. 39
5.13 LAST SETTING MEMORY………………………………………………………………………
Pg. 39
5.14 SERIES OPERATION…………………………………………………………………………….
Pg. 39
5.14.1 Series connection for
increased output vol
t
age…………………………………………
Pg. 40
5.14.2 Series connection for positive and negative output vol
t
age……………………………
Pg. 41
5.15 PARALLEL OPERATION……………………………………………………………………….
Pg. 42