Filter
Top Products
This unit employs the YAMAHA Parametric Room Acoustic Optimizer (YPAO)
technology for automatic sound beam optimization.
• Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure.
Make sure that there are no children around in the listening room while the AUTO SETUP
procedure is in progress.
• Make sure that your listening room is as quiet as possible while the AUTO SETUP procedure is in
progress.
1 Press STANDBY/ON to turn on the power of this unit.
If a subwoofer with adjustable volume and crossover/high cut frequency controls is
connected to this unit, set the volume between 11 and 1 o’clock as viewed on a
conventional clockface and set the crossover/high cut frequency to the maximum.
2 Turn on the power of your TV.
3 Switch to the video input on your TV using the remote control supplied
with the TV.
For example, if you connect the supplied video pin cable to the video input 2 jack of
your TV, switch to video input 2 on your TV.
4 Press MENU.
5 Press / to select AUTO SETUP and then press ENTER.
6 Press / to select BEAM OPT+SOUND OPTIMZ and then press
ENTER.
7 Press / / / to select and configure each parameter and then
press ENTER.
INSTALLING (Installing)
Use to select the installed position of the unit in your listening room.
• Select Angle to Wall or corner if the unit is installed in the corner.
• Select Parallel to Wall if the unit is installed in parallel with the wall.
MOUNTING (Mounting)
Use to select the mounted position of the unit in your listening room.
• Select WALL if the unit is mounted on the wall.
• Select SHELF if the unit is mounted on the shelf.
REFLECTING (Reflecting)
Use to select the reflectivity of your listening room.
• Select NORMAL if your listening room has a normal reflectivity.
• Select HI ECHO if your listening room has highly reflective surfaces such as concrete
walls.
8 Press ENTER to start the AUTO SETUP procedure.
ENVIRONMENT CHECK (Environmental noise check), SUB WOOFER CHECK
(Subwoofer check) and WILL START in 10 SEC (Will start in 10 sec) are displayed
in order as the PREPARATION procedure is in progress. It takes about three minutes
for the entire AUTO SETUP procedure to be completed.
y
If an error occurs, an error message is displayed. See “Error messages for AUTO SETUP” on
page 35 in the Owner’s Manual for a complete list of error messages and their proper remedies.
Follow the instructions and press RETURN to perform the AUTO SETUP procedure again.
9 Check that the following screen is displayed on your TV.
10 Press ENTER to confirm the results.
■ Enjoying TV in surround sound
y
Before performing the steps below, set the volume of this unit to –40 dB.
1 Select the TV channel you want to watch using the remote control
supplied with your TV.
2 Press TV to select TV as the input source.
3 If you hear sound output from your TV speakers, turn down the volume
level using the remote control supplied with your TV until you cannot
hear any sound.
4 Press VOLUME +/– to adjust the volume level.
5 Press YSP to switch to the operation mode of this unit.
6 Press one of the beam mode buttons to select the desired beam mode.
For further details about the beam modes, see page 42 in the supplied Owner’s Manual.
y
The target mode outputs sound beams in a single channel and is ideal if you do not want the sound
beams to be reflected on the walls in your listening room or if you do not disturb others asleep while
enjoying music or movies at night. In addition, you can adjust the horizontal angle of the sound beams
so that you can hear dialogues clearly even from a distant location such as the kitchen area in your
listening room. For further details about the target mode, see page 45 in the supplied Owner’s Manual.
7 Press VOL MODE repeatedly to select the desired volume mode.
The volume modes are designed to improve listenability at lower volumes and limit the
volume level of the TV so that it will not vary suddenly to a great extent.
For further details about the volume modes, see page 56 in the supplied Owner’s Manual.
■ Enjoying DVDs in surround sound
y
Before performing the steps below, set the volume of this unit to –40 dB.
1 Switch to the video input on your TV using the remote control supplied
with your TV so that the DVD menu screen is displayed.
2 Press DVD to select DVD as the input source and then start playback on
the DVD player.
3 If you hear sound output from your TV speakers, turn down the volume
level using the remote control supplied with your TV until you cannot
hear any sound.
4 Press VOLUME +/– to adjust the volume level.
5 Press YSP to switch to the operation mode of this unit.
6 Press one of the beam mode buttons to select the desired beam mode.
For further details about the beam modes, see page 42 in the supplied Owner’s
Manual.
Automatically setting up the listening environment Enjoying surround sound
Notes
TV
POWER
SLEEP
AV
POWER
STANDBY/ON
INPUTMODE
MACROINPUT2INPUT1
TV
STBVCRDVD
AUX
YSP
CH LEVEL MENU
RETURN
TEST
ENTER
CINEMA DSP
.;MEMORY
;AUTO SETUP
;BASIC SETUP
;MANUAL SETUP
[]/[]:Up/Down
[ENTER]:Enter
p
p
SET MENU
CH LEVEL MENU
RETURN
TEST
ENTER
CINEMA DSP
.BEAM+SOUND OPTIMZ
BEAM OPTIMZ only
SOUND OPTIMZ only
[]/[]:Up/Down
[ENTER]:Enter
p
p
;
AUTO SETUP
CH LEVEL MENU
RETURN
TEST
ENTER
CINEMA DSP
.INSTALLING;;Parallel to Wall
MOUNTING;;;;SHELF
REFLECTING;;NORMAL
Set MIC in front of YSP
MIN 2m/6.5ft
[]/[]:Up/Down/[ ]/[ ]:Sel
[ENTER]:Start
p
p
PREPARATION
p
p
CH LEVEL MENU
RETURN
TEST
ENTER
CINEMA DSP
CH LEVEL MENU
RETURN
TEST
ENTER
CINEMA DSP
.ENVIRONMENT CHECK
;;;[OK]
SUB WOOFER CHECK
;;;[NOT IN USE]
WILL START in 10 SEC
Move aside or behind YSP
*****-----
PREPARATION
BEAM MODE: 5BEAM
SUBWOOFER: NOT APPLICABLE
[ENTER]:Enter
[RETURN]:Cancel
SHOW RESULT
Example of the
SHOW RESULT screen
CH LEVEL MENU
RETURN
TEST
ENTER
CINEMA DSP
AUTO SETTING COMPLETED
TV
POWER
SLEEP
AV
POWER
STANDBY/ON
INPUTMODE
MACROINPUT2INPUT1
TV
STBVCRDVD
AUX
YSP
TV VOL
VOLUME
CH
2
1
STEREO
SLEEP
3
4
56
5BEAM
ST+3BEAM
3BEAM
TARGET
INPUTMODE
MACROINPUT2INPUT1
AUX
YSP
2
1
STEREO
SURROUND
OFF
SPORTS
3
4
56
789
0
+10
5BEAM
ST+3BEAM
3BEAM
TARGET
MUSIC MOVIE VOL MODE
STEREO
SURROUND
OFF
SPORTS
4
56
789
0
+10
TARGET
MUSIC MOVIE VOL MODE
TV
POWER
SLEEP
AV
POWER
STANDBY/ON
INPUTMODE
MACROINPUT2INPUT1
TV
STBVCRDVD
AUX
YSP
TV VOL
VOLUME
CH
2
1
STEREO
SLEEP
3
4
56
5BEAM
ST+3BEAM
3BEAM
TARGET
INPUTMODE
MACROINPUT2INPUT1
AUX
YSP
2
1
STEREO
SURROUND
OFF
SPORTS
3
4
56
789
0
+10
5BEAM
ST+3BEAM
3BEAM
TARGET
MUSIC MOVIE VOL MODE
YSP-1000 Quick Reference Guide.fm Page 2 Tuesday, August 30, 2005 6:58 PM