Filter
Top Products
Use the left/right [PARAMETER/VALUE]
keys to move the flashing section, and use the
up/down [PARAMETER/VALUE] keys to
change the number.
5.
Press the [ENTER/YES] key.
A screen will appear that allows you to set a
start point for the erase action.
6.
Use the [PARAMETER/VALUE]
keys to specify the start point for
the segment to be erased.
The start location can be specified in two
ways.
For information on how to specify the
position, see page 40.
7.
When you have specified the start
point, press the [ENTER/YES] key.
A screen will appear that allows you to set
the end point for the erase action.
8.
Specify the end point in the same
way as described in step 6.
9.
When you have specified the end
point, press the [ENTER/YES] key.
The display changes as follows.
10.
To execute the erase process,
press the [ENTER/YES] key.
While erasing is in progress, the remaining
time is shown on the display as a percentage,
such as "doinG90". When the copy is
complete, the "tr Edit" screen returns.
The length of the processing interval depends on
setting conditions.
By pressing the [EXIT/NO] key instead of
the [ENTER/YES] key, you can return to the
display of the preceding step and make
changes.
Erasing an entire track
This operation erases all recorded data from
the specified track/V-take.
1.
While the main screen is shown,
press the [TRACK PARAMETER]
key.
The track parameter menu appears.
2.
Use the status keys 1 – 4 to select
the track to be erased. Then use
the left/right [PARAMETER/VALUE]
keys to call up the screen for
selecting the V-take.
The track number and V-take number are
shown.
3.
Press the [ENTER/YES] key.
The display changes as follows.
4.
Press the [ENTER/YES] key.
The track number and V-take number to be
erased are shown. (In the initial condition,
this is the V-take currently set for the track
selected in step 2.)
ER T1-1
Track number
V-take number
ERASE
T1-1
NOTE
YES NO
105560
103560
Reference [Track Editing]
ZOOM MRS-4
43
5.
If necessary, specify the track
number and V-take number, and
press the [ENTER/YES] key.
Use the left/right [PARAMETER/VALUE]
keys to move the flashing section, and use the
up/down [PARAMETER/VALUE] keys to
change the number. You can also specify a V-
take that is currently not selected for the
track.
When you press the [ENTER/YES] key, the
copy destination track number and V-take
number are shown.
6.
Specify the copy destination track
and V-take in the same way as
described in step 5.
7.
Press the [ENTER/YES] key.
The display changes as follows.
8.
To execute the copy, press the
[ENTER/YES] key.
While the copy is in progress, the remaining
time is shown on the display as a percentage,
such as "doinG90". When the copy is
complete, the V-take selection screen returns.
The length of the processing interval depends on
setting conditions.
By pressing the [EXIT/NO] key instead of
the [ENTER/YES] key, you can return to the
display of the preceding step and make
changes.
Erasing a specified
segment
This operation erases the recorded data from
the specified segment of a track, returning it
to a silent (blank) state.
1.
While the main screen is shown,
press the [SONG/UTILITY/TUNER]
key.
The display will show the song number.
2.
Press the right [PARAMETER/
VALUE] key once to bring up the
indication "tr Edit" (track edit) on
the display. Then press the
[ENTER/YES] key.
The first item of the track edit menu appears.
3.
Press the right [PARAMETER/
VALUE] key once to bring up the
indication "tr Ers" (track erase) on
the display. Then press the
[ENTER/YES] key.
The screen for specifying the track and V-
take to erase appears.
4.
Use the [PARAMETER/VALUE]
keys to specify the track and V-
take to erase.
SRC 1-1
TR ERS
Track number V-take number
TR COPY
NOTE
YES NO
CP T1-1
Copy destination
track number
Copy destination
V-take number
CP T1-1
COPY
Copy source
track number
Copy source
V-take number
ZOOM MRS-4
Reference [Track Editing]
42