Filter
Top Products
40 XTP CrossPoint 1600 and 3200 • Remote Control 41XTP CrossPoint 1600 and 3200 • Remote Control
Command SIS Command
(Host to Unit to Endpoint)
Response
(Endpoint to Unit to Host)
Additional Description
Input audio selection
NOTE: These commands select between the audio embedded in the digital video stream and the 2-channel analog audio.
Input audio selection
E
I
X!
*
X1!
AFMT
}
AfmtI
X!
*
X1!]
Example:
E
I1*0AFMT
}
AfmtI1*0
]
Auto (0): Digital audio takes priority over analog audio.
View input audio selection
E
I
X!
AFMT
} X1!]
View all input audio
selections
E
IAFMT
} X1!
1
X1!
2
X1!
3
...
X1!
n
]
Each
X1!
is the enable or disable status of an output, starting
at output 1. n is 16 or 32.
Audio input gain and attenuation
NOTE: The set gain (G) and set attenuation (g) commands are case sensitive.
Set input level to +dB value
X!
*
X1@
G In
X!
•Aud
X1#]
Example:
1*2G
In01•Aud+02
]
Set input 1 audio gain to +2 dB.
Set input level to -dB value
X!
*
X1$
g In
X!
•Aud
X1#]
Increment gain
X!
+G In
X!
•Aud
X1#]
Increase gain by 1 dB.
Example:
5+G
In05•Aud+03
]
Increase audio input 5 level from +2 dB to +3 dB.
Decrement gain
X!
–G In
X!
•Aud
X1#]
Decrease gain by 1 dB.
Read input level
X!
G
X1#]
NOTE: • = Space
X!
= Input number 01 – 16 or 32
X1!
= Input audio source 0 = auto (see the example above) 2 = Analog (local 2-channel audio)
1 = HDMI (de-embedded digital audio) (default)
X1@
= Audio gain 0 to +24 (1 dB per step)
X1#
= Numeric dB value –18 to +24 (45 steps of gain or attenuation) (Default = 0 dB)
X1$
= Audio attenuation 1 – 18 (1 dB per step)
Command SIS Command
(Host to Unit to Endpoint)
Response
(Endpoint to Unit to Host)
Additional Description
List Digital Sync Validation Processing (DSVP)
List sync of all inputs
0LS
X1&
1
X1&
2
X1&
3
...
X1&
n
]
16 or 32 (
n
)
X1&
s; each is the signal status of an input, starting
from input 1.
Example
(XTP CrossPoint 3200):
0LS
Input:
Response Status:
no input detected
input detected
1 2345
6
732
0 0 0 1 1 1 0 . . . 0
SIS Command and Response Table for IP-Specific Commands
NOTE: These commands allow you to control and monitor the IP functions of the XTP CrossPoint matrix switcher .
Command SIS Command (host to unit) Response (unit to host)
Additional Description
IP and serial port setup
Set IP address
EX2(
CI
}
Ipi
X2(]
Default: 192.168.254.254
Read IP address
E
CI
} X2(]
Set subnet mask
EX2(
CS
}
Ips
X2(]
Default: 255.255.0.0
Read subnet mask
E
CS
} X2(]
Set gateway IP address
EX2(
CG
}
Ipg
X2(]
Default: 0.0.0.0
Read gateway IP address
E
CG
} X2(]
Set DHCP on or off
EX3)
DH
}
Idh
X3)]
Default: 0 (Off)
Read DHCP on/off status
E
DH
} X3)]
NOTE:
X1&
= Signal detection status 0 = no input connected 1 = input connected
X2(
= IP address nnn.nnn.nnn.nnn
X3)
= DHCP 0 = off, 1 = on