Filter
Top Products
No.517811-22
DLA-M2000LU
DLA-M2000LE
34
Basic Operations
■ Projector’s buttons
■ Remote control unit
Turning off Image and Sound (HIDE)
Video image and audio sound can be temporarily turned off.
Press the HIDE button once:
Video image and audio sound instantly turn off.
Press the HIDE button again:
Video image and audio sound come on again.
Note
• When the projected image input is changed, the HIDE
function is canceled and the image and sound return.
Removing the Trapezoidal Distortion of
the Image
If the image projected on the screen is distorted in trapezoid
form, correct it with the KEYSTONE buttons on the projector.
When the KEYSTONE button is pressed, “Keystone”
appears on the screen together with the level bar and set
value (–80 to 128). When “15 sec.” is displayed in the menu,
“Keystone” will appear in approximately 15 seconds.
When you press the KEYSTONE button:
The trapezoid form is corrected as shown in the figure.
When you press the KEYSTONE button:
The top bottom inverted trapezoid form is corrected as
shown in the figure.
* To cancel correction and restore the original screen, press
the PRESET button.
(Adjusted value:0)
* Press the ESCAPE button to immediately remove the
keystone display.
Notes
• The trapezoidal distortion (keystone) can be adjusted from the
option menu. (Refer to page 52.)
• The range of the trapezoidal distortion adjustment is
approximately 20° in the vertical direction.
• Interference patterns may appear on the screen when
adjusting the keystone. This is not a malfunction.
• Depending on the type of signal, some noise may appear in
the picture when the keystone is adjusted.
This is not a malfunction.
HIDE
button
KEYSTONE
/ button
LAMP TEMP
STAND BY
HIDE
PC
VIDEO
MENU
KEYSTONE VOLUME
PRESET
ESCAPE ENTER
OPERATE
PRESET
button
ESCAPE
button
HIDE
button
ESCAPE
button
U
T
D
W
FOCUS
–
+
ZOOM
SHIFT
VOLUME
–
+
QUICK
ALIGN.
SHUTER
–
+
E
N
T
E
R
HIDE
OPERATE
PRESET
ESCAPE
DIGITAL
ZOOM
KEYSTONE
PC
+
–
VIC SELECT
MENU
FREEZE
VIDEO
RM-M2000 REMOTE CONTROL UNIT
KEYSTONE
/ button
PRESET
button
HIDE
HIDE
Remote control unit Projector
Keystone 123
KEYSTONE
KEYSTONE
KEYSTONE
KEYSTONE
Projected image with trapezoidal distortion
Remote control unit Projector
35
Basic Operations
ENGLISHDEUTSHFRANÇAISITALIANOESPAÑOL
■ Remote control unit
Quick Alignment Function
(QUICK ALIGN.)
The Quick Alignment function automatically adjusts (sets)
the screen settings of the image input from the PC1 or PC2
input terminals. This can only be performed from the remote
control.
While projecting an image on the screen, press the QUICK
ALIGN. button on the remote control.
Quick alignment is conducted to obtain best image.
* During the automatic alignment, “Quick Alignment” appears
on the screen, and then disappears when the alignment is
completed.
[Screen display]
Notes
• This only works for the signals input from the PC1 or PC2 input
terminals. It does not work for the signals input from the AV IN
terminal (VIDEO or Y/C input terminal).
• The quick alignment function is used to automatically adjust
the “Brightness”, “Contrast”, “Horizontal and vertical
position”, “Phase” and “Tracking” of the projected image.
• When using the quick alignment function to automatically
adjust the image, use a bright, still-picture. It may not
function correctly on a dark or motion picture. If the results
obtained with the quick alignment function are not
satisfactory, manually adjust the “Brightness”, “Contrast”,
“Horizontal and vertical position”, “Phase” and “Tracking” of
the projected image.
U
T
D
W
RM-M2000 REMOTE CONTROL UNIT
FOCUS
–
+
ZOOM
SHIFT
VOLUME
–
+
QUICK
ALIGN.
SHUTTER
–
+
E
N
T
E
R
HIDE
OPERATE
PRESET
ESCAPE
DIGITAL
ZOOM
KEYSTONE
PC
+
–
VIC SELECT
MENU
FREEZE
VIDEO
QUICK ALIGN. button
QUICK
ALIGN.
Remote control unit
Quick Alignment