Filter
Top Products
21
ENGLISH
3
Press 2/3 to select the desired amount
of time.
Select the number of minutes before the Monitor goes
into standby mode after the signal has ceased to be
supplied.
Each time you press the button, the amount of time
changes as follows:
To cancel the Power Saving function, select “OFF.”
4
Press MENU/EXIT (or MENU on the
Monitor) twice to exit from the menu
operations.
Prohibiting the Monitor’s Button Operations
This function allows you to prohibit the button operations on
the Monitor to prevent malfunction or avoid tampering.
1
On the remote control:
Press MENU/EXIT while holding
VOLUME – to display the Setup Menu.
On the Monitor:
Press MENU while holding 2 to display
the Setup Menu.
2
Press 5/∞ to move the cursor (3) to
“CONTROL LOCK.”
3
Press 2/3 to select the desired setting.
Each time you press the button, the Control Lock
function alternates between “ON” and “OFF.”
To cancel the Control Lock function, select “OFF.”
4
Press MENU/EXIT (or MENU on the
Monitor) twice to exit from the menu
operations.
Note:
• Even when the Control Lock function is in use, the
following operations are possible:
– Operation to cancel the Control Lock function
– All operations from the remote control
Cursor (3)
OFF 1 MIN. 2 MIN. 3 MIN. 4 MIN. 5 MIN.
Cursor (3)
POWER SAVE
CONTROL LOCK
STATUS DISPLAY
SCREEN SAVER
WHITE BACK
VENTILATION MODE
WHITE BALANCE
all reset
HOUR METER x100h
SET-UP MENU
ADJUST:
SELECT:
EXIT:
MENU
: 1MIN.
: ON
: ON
: ON
: ON
: H
: 001
Confirming the Use Time
You can confirm the hours of use on the Setup Menu.
This may be necessary when you ask for any service.
1
On the remote control:
Press MENU/EXIT while holding
VOLUME – to display the Setup Menu.
On the Monitor:
Press MENU while holding 2 to display
the Setup Menu.
2
Confirm the hour of use.
• The displayed value for the hours of use is divided by
100. To calculate the actual hours of use, multiply the
displayed value by 100.
3
Press MENU/EXIT (or MENU on the
Monitor) twice to exit from the menu
operations.
Notes:
• The value for the hours of use is added by one hour unit. If
you use the monitor within one hour. It will not be added to
the hours of use.
• The period when the monitor is on standby (the power
lamp glows red) will not be added to the hours of use.
Setting the Power Saving Function
This function allows you to turn off (into standby mode)
automatically when no signal comes in for a certain period of
time.
1
On the remote control:
Press MENU/EXIT while holding
VOLUME – to display the Setup Menu.
On the Monitor:
Press MENU while holding 2 to display
the Setup Menu.
2
Press 5/∞ to move the cursor (3) to
“POWER SAVE.”
Hours of use
Cursor (3)
POWER SAVE
CONTROL LOCK
STATUS DISPLAY
SCREEN SAVER
WHITE BACK
VENTILATION MODE
WHITE BALANCE
all reset
HOUR METER x100h
SET-UP MENU
ADJUST:
SELECT:
EXIT:
MENU
: 1MIN.
: ON
: ON
: ON
: ON
: H
: 001
POWER SAVE
CONTROL LOCK
STATUS DISPLAY
SCREEN SAVER
WHITE BACK
VENTILATION MODE
WHITE BALANCE
all reset
HOUR METER x100h
SET-UP MENU
ADJUST:
SELECT:
EXIT:
MENU
: 1MIN.
: ON
: ON
: ON
: ON
: H
: 001
20-23.GD-V4200PZW-A[EN]/f 00.2.23, 5:20 PM21