Filter
Top Products
4
ENGLISH
• Replacing the lamp runs the risk of burns and electric
shock, therefore shut off power supply, unplug the AC
power cable from its electrical outlet and wait at least 60 min
for the lamp to cool down before attempting to replace it.
• If the lamp breaks, contact your nearest Marantz Authorized
Dealer or Service Center.
• Before replacing the lamp, read carefully “Lamp Handling
Precautions” (
☞
pg. 1) and “Lamp Unit Replacement”
(
☞
pg. 36). Replace the lamp as explained therein.
• The lens of this projector can be changed as liked. (LN-
10VP32/LN-10VP40/LN-10VP53) With the right lens, you
can set the projection distance and screen size according
to the environment of use.
* The above projections distances are given for a
screen with an aspect ratio of 16:9. For screen sizes
and projection distances by lens, see pg. 13-14.
• To change the lens, contact your nearest Marantz
Authorized Dealer or Service Center.
Do not change the lens yourself.
• The lenses used with this projector are as follows.
Lens Changes
RS-232CDVI-D INRGB IN
EXT.INT.
IN
OUT
OFF ON
1
2
TRIG. LIGHT
REMOTE
VIDEO IN
S-VIDEO IN COMPONENT VIDEO IN 1 COMPONENT VIDEO IN 2
YP
B
/C
B
P
R
/C
R
YP
B
/C
B
P
R
/C
R
CAUTION
HIGH-PRESSURE LAMP MAY EXPLODE IF IMPROPERLY
HANDLED. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION HOT
UNPLUG THE POWER CORD AND WAIT 60
MINUTES BEFORE CHANGING THE LAMP.
ATTENTION
LA LAMPE SOUS HAUTE PRESSION PEUT EXPLOSER
SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN
QUALIFIE.
VORSICHT
BEI FALSCHER HANDHABUNG KANN DIE
HOCHDRUCKLAMPE EXPLODIEREN UBERLASSEN SIE
WARTUNGSARBEITEN NUR FACHPERSONAL.
ATTENTION CHAUD
DEBRANCER LE CORD ON D'ALIMENTION ET
ATENDER 60 MINUTES AVANT DE CHANGER
LAMPE.
WARNUNG HEISS
ZIEHEN SIE DEN NETZSTECKER AB UND
WARTEN SIE 60 MINUTEN BEVOR SIE DIE
GLUHLAMPE WECHSELN.
CAUTION
HIGH-PRESSURE LAMP MAY EXPLODE IF IMPROPERLY
HANDLED. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION HOT
UNPLUG THE POWER CORD AND WAIT 60
MINUTES BEFORE CHANGING THE LAMP.
ATTENTION
LA LAMPE SOUS HAUTE PRESSION PEUT EXPLOSER
SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN
QUALIFIE.
VORSICHT
BEI FALSCHER HANDHABUNG KANN DIE
HOCHDRUCKLAMPE EXPLODIEREN UBERLASSEN SIE
WARTUNGSARBEITEN NUR FACHPERSONAL.
ATTENTION CHAUD
DEBRANCER LE CORD ON D'ALIMENTION ET
ATENDER 60 MINUTES AVANT DE CHANGER
LAMPE.
WARNUNG HEISS
ZIEHEN SIE DEN NETZSTECKER AB UND
WARTEN SIE 60 MINUTEN BEVOR SIE DIE
GLUHLAMPE WECHSELN.
Lamp Replacement Precautions
Lens Projection distance of 100 inch image
LN10VP32 Approx. 3.19 to 3.98 m
LN10VP40 Approx. 3.98 to 5.31 m
LN10VP53 Approx. 5.31 to 7.97 m
Projector Lens
(Found on rear panel nameplate)
VP10S1L32/N1M LN10VP32
VP10S1L40/N1M LN10VP40
VP10S1L53/N1M LN10VP53