Filter
Top Products
Index
Multi-Tech Systems, Inc. SocketModem MT5600SMI Developer’s Guide 133
leased line operation command &L, 70
Line feed character S4, 75
load flash memory command **, 34
local analog loopback test command &T, 33
M
Mechanical specifications, 8
MNP extended services command -K, 59
modem-on-hold enable command +PMH, 71
modem-on-hold timer command +PMHTR, 72
modulation reporting control command +MR, 53
modulation selection command +MS, 51
N
New Zealand Telecom Warning Notice, 129
O
Online command mode, 29
operating conditions, 14
operating mode command \N, 31
P
Parallel Demo Board block diagram, 117
Parallel Host Interface, 18
Parallel Interface Registers Table, 19
Parallel Pin configurations, 11
Part 68 of the FCC rules, 125
PC Board Layout Guidelines, 121
PCM upstream ignore command +PIG, 73
Phase 1 and Phase 2 control command +PQC, 73
Physical dimensions, 8
plug and plag vendor ID and product number
command %8, 34
plug and play serial number command %7, 33
Programmable Baud Rates Table, 27
Q
quiet result code control command Q, 36
R
Receiver FIFO Interrupt Operation, 28
Register Signal Definitions, 20
report line signal level command %L, 47
report line signal quality command %Q, 47
report retrieved with Caller ID command +VRID, 30
report the current error control command +ER
<type>, 57
request complete capabilities command +GCAP, 32
request model identification command +GMM, 32
request modem manufacturer command +GMI, 31
request revision identification command +GMR, 32
restore factory default configuration (profile)
command &F, 32
result code form command V, 36
Result codes, 29, 83
return to on-line data mode command O, 43
Rings S0, setting number of, 75
RLSD (DCD) option command &C, 38
RTS/CTS option command &R, 39
S
Safety considerations, 122
select Bell or CCITT modulation command B, 54
select Fax Class 1 command +FCLASS=1, 90
select Fax Class 1.0 command +FCLASS=1.0, 90
select guard tone command &G, 44
select pulse dial make/break ratio command &P, 44
select the active service class command +FCLASS,
30
selective repeat command +ESR, 56
selects µ-Law or A-Law codec type command %U, 54
Serial Demo Board block diagram, 116
Serial Pin configurations, 9
Serial Test/Demo Board Components, 115
Set pulse dial default command P, 42
set telephony extension command -STE, 48
Set tone dial default command T, 42
single line connect message enable command \V, 47
Soft reset and restore profile command Z, 30
South African Statement, Regulations, 129
speaker control command M, 44
speaker volume command L, 44
Specifications, technical, 7
S-registers, 75
S0, 75
S1, 75
S10, 76
S11, 76
S11-20, 76
S12, 76
S14, 76
S16, 76
S2, 75
S21, 77
S210, 82
S22, 77
S23, 77
S24, 77
S25, 77
S26, 77
S27, 78
S28, 78
S29, 78
S3, 75
S30, 78
S31, 78
S36, 79
S38, 79
S39, 79
S4, 75
S40, 79
S41, 80
S46, 80
S48, 80
S5, 75
S6, 75
S7, 75
S8, 75
S86, 81
S9, 76
S91, 81
S95, 81
store current configuration command &W, 33
store telephone number command &Z, 33