Paradyne 3611 Computer Drive User Manual


 
D-13610-A2-GB41-60 March 1999
Configuration Scenarios
Overview D-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDM Configuration Scenarios D-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDM Scenario 1 – Using Two Synchronous Channels D-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDM Scenario 2 – Using Switched 56 kbps Dial Backup D-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Bridge Configuration Scenarios D-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Partial Backup D-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full Backup D-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multipoint Full Dial Backup with Nondisruptive Diagnostics D-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Partial Backup Using an Extended Bridge D-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Management-Controlled Full Backup Using an Extended Bridge D-19. . . . . . . . . . . . . . . . . . . .
MCMP Configuration Scenarios D-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCMP Using FEP Port Sharing D-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dedicated MCMP Backup with Switched 56 DBMs D-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCMP Backup Using FEP Port Sharing D-30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview
This appendix presents a subset of various
configuration scenarios for TDM, digital bridge, and
MCMP applications; these examples are not inclusive of
all possible configurations. Each scenario consists of an
illustration, an explanation of the configuration shown,
and the applicable configuration option settings needed to
support that scenario. Refer to Chapter 5 for additional
configuration information.
When reviewing the configuration options, keep the
following in mind:
A set of configuration options is provided for each
type of unit (e.g., a control or a central-site bridge)
shown in an illustration.
The Configuration Worksheet you would use to
record the unit’s configuration is identified.
Configuration options are grouped by their option
set (the set of configuration options that can be
edited under the Opts submenu – DSU, Diag,
DBM, etc.).
Option sets, as well as the configuration options,
are presented in the order you will see them (option
sets are bulleted and in bold), with one exception –
when the TDM or MCMP option is installed, the
MUX and PrtSp option set settings are configured
first. (Note: N/A means Not Applicable.)
Only applicable configuration options are listed;
unlisted configuration options are left at their
default settings or are forced to a value based upon
other configuration option settings.
Individual configuration options are shown as they
appear on the DCP, followed by a colon (:) and the
value that should be set (selected).
D