Filter
Top Products
83
-
507
-
013 Rev. D
TABLE OF CONTENTS
3.8.
8 Address se
t
ting……………….……………………………………………………………..
Pg. 18
3.8.9 Baud rate se
t
ting…………………………………………………………………………….
Pg. 18
3.9 CONNECTING THE LOAD………………………………………………………………………..
Pg. 18
3.9.1 Load Wi
r
ing…………………………………………………………………………………..
Pg. 18
3.9.2 Current Carrying Capa
c
ity………………………………………………………………….
Pg. 18
3.9.3 Wire termination…………………………………………………………………………….
Pg. 19
3.9.4 Noise and Impedance E
f
fects……………………………………………………………...
Pg. 20
3.9.5 Inductive loads……………………………………
………………………………………….
Pg. 20
3.9.6 Making the load conne
c
tions……………………………………………………………….
Pg. 20
3.9.7 Connecting single loads, local sensing (d
e
fault)…………………………………………
Pg. 23
3.9.8 Connecting single loads, remote sen
s
ing………………………………………………
...
Pg. 23
3.9.9 Connecting multiple loads, radial distribution method…………...……………………...
Pg. 23
3.9.10 Multiple loads connection with distribution term
i
nals…………………………………..
Pg. 24
3.9.11 Grounding ou
t
puts…………………………………………………………………………
Pg. 24
3.10 LOCAL AND REMOTE SENSING………………………………………………………………
Pg. 25
3.10.1 Sensing wi
r
ing……………………………………………………………………………...
Pg. 25
3.10.2 Local sen
s
ing……………………………………………………………………………….
Pg. 25
3.10.3 Remote sen
s
ing…………………………………………………………
…………………
Pg. 26
3.10.4 J2 sense connector technical inform
a
tion………………………………………………
Pg. 26
3.11 REPACKAGING FOR SHIPMENT………………………………………………………………
Pg. 26
CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS
………...………
Pg. 27
4.1 INTRODUCTION……………
………………………………………………………………………
Pg. 27
4.2 FRONT PANELCONTROLS AND INDICATORS……………………………………………….
Pg. 27
4.3 REAR PANELCONNECTIONS AND CONTROLS……………………………………………..
Pg. 29
4.4 REAR PANEL SW1 SETUP SWITCH……………………………………………………………
Pg. 30
4.4.1 SW1 position
s fun
c
tions……………………………………………………………………
Pg. 31
4.4.2 Resetting the SW1 switch………………………………………………………………
Pg. 31
4.5 REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR……………………
Pg. 32
4.5.1 Making J1 conne
c
tions……………………………………………………………………..
Pg. 32
CHAPTER 5 LOCAL OPERATION
………………………………………………………………….
Pg. 34
5.1 INTRODUCTION…………………………………………………………………………………..
Pg. 34
5.2 STANDARD OPERATION…………………………………………………………………………
Pg. 34
5.2.1 Constant Voltage Mode…………………………………………………………………….
Pg. 34
5.2.2 Constant Current Oper
a
tion………………………………………………………………..
Pg. 34
5.2.3 Automatic Cros
s
over………………………………………………………………………..
Pg. 35
5.3 OVER VOLTAGE PROTECTION (OVP)………………………………………………………...
Pg. 35
5.3.1 Setting the OVP level………………………………………
……………………………….
Pg. 35
5.3.2 Activated OVP protection indic
a
tions……………………………………………………..
Pg. 35
5.3.3 Resetting the OVP ci
r
cuit…………………………………………………………………..
Pg. 35
5.4 UNDER VOLTAGE LIMIT……………………………………………………………………….. .
Pg. 36
5.4.1 Sett
ing the UVL level………………………………………………………………………..
Pg. 36
5.5 FOLDBACK PROTECTION……………………………………………………………………….
Pg. 36
5.5.1 Setting the Foldback prote
c
tion…………………………………………………………….
Pg. 36
5.5.2 Resetting activated Foldback prote
c
tion……………………………………
……………..
Pg. 36
5.6 OUTPUT ON/OFF CONTROL…………………………………………………………………….
Pg. 36
5.7 OUTPUT SHUT
-
OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR………………
Pg. 36
5.8 ENABLE/DISABLE CONTROL VIA………………………………………………………………
Pg. 37
5.9 CV/CC SIGNAL…………………………………………………………………
…………………..
Pg. 37
5.10 PS OK SIGNAL……………………………………………………………………………………
Pg. 37
5.11 SAFE START AND AUTO
-
RESTART MODES………………………………………………..
Pg. 38
5.11.1 Automatic start mode………………………………………………………………………
Pg. 38
5.11.2 Safe start mode…………………………………………
…………………………………..
Pg. 38
5.12 OVER TEMPERATURE PROTECTION (OTP)………………………………………………..
Pg. 38
5.13 LAST SETTING MEMORY………………………………………………………………………
Pg. 38
5.14 SERIES OPERATION…………………………………………………………………………….
Pg. 39
5.14.1 Series connection for increased
output vol
t
age…………………………………………
Pg. 39
5.14.2 Series connection for positive and negative output vol
t
age……………………………
Pg. 40
5.15 PARALLEL OPERATION……………………………………………………………………….
Pg. 41