Filter
Top Products
20 Software Release Note AlliedWare Plus Version 5.4.3-0.1 C613-10508-01-REV B
ipv6 pim rp
embedded
New N Y Y Y Y PIM-SMv6
Commands
Use this command to configure and enable
embedded RP (Rendezvous Point) in PIM-
SMv6.
ipv6 pim rp-
address
New N Y Y Y Y PIM-SMv6
Commands
Use this command to statically configure RP
(Rendezvous Point) address for IPv6 multicast
groups.
ipv6 pim rp-
candidate
New N Y Y Y Y PIM-SMv6
Commands
Use this command to make the switch an RP
(Rendezvous Point) candidate using the IPv6
address of the specified VLAN interface.
ipv6 pim rp-
register-kat
New N Y Y Y Y PIM-SMv6
Commands
Use this command to configure the Keep
Alive Time (KAT) for (S,G) states at the RP
(Rendezvous Point) to monitor PIM-SMv6
Register packets.
ipv6 pim
sparse-mode
New N Y Y Y Y PIM-SMv6
Commands
Use this command to enable PIM-SMv6 on a
VLAN interface.
ipv6 pim
sparse-mode
passive
New N Y Y Y Y PIM-SMv6
Commands
Use this command to enable and disable PIM-
SMv6 passive mode operation for local
members on a VLAN interface.
ipv6 pim spt-
threshold
New N Y Y Y Y PIM-SMv6
Commands
Use this command to turn on the ability for
the last-hop PIM-SMv6 router to switch to the
SPT (Shortest Path Tree).
ipv6 pim spt-
threshold
group-list
New N Y Y Y Y PIM-SMv6
Commands
Use this command to turn on/off the ability
for the last-hop PIM-SMv6 router to switch to
the SPT (Shortest Path Tree) for multicast
group addresses specified by the given IPv6
access-list.
ipv6 pim
unicast-bsm
New N Y Y Y Y PIM-SMv6
Commands
Use this command to enable support for the
sending and receiving of unicast Boot Strap
Messages (BSM) on a VLAN interface.
show
debugging
ipv6 pim
sparse-mode
New N Y Y Y Y PIM-SMv6
Commands
Use this command to display the status of the
PIM-SMv6 debugging on your switch.
show ipv6 pim
sparse-mode
bsr-router
New N Y Y Y Y PIM-SMv6
Commands
Use this command to show the PIM-SMv6
Bootstrap Router (BSR) IPv6 address.
show ipv6 pim
sparse-mode
interface
New N Y Y Y Y PIM-SMv6
Commands
Use this command to show PIM-SMv6
interface information. Note that you can
specify an individual VLAN interface with the
optional parameter. Alternatively, you can
display PIM-SMv6 interface information for all
interfaces if you omit the optional
interface parameter.
show ipv6 pim
sparse-mode
interface detail
New N Y Y Y Y PIM-SMv6
Commands
Use this command to show detailed PIM-
SMv6 information for all PIM-SMv6
configured interfaces.
show ipv6 pim
sparse-mode
local-members
New N Y Y Y Y PIM-SMv6
Commands
Use this command to show detailed local
member information on a VLAN interface
configured for PIM-SMv6. If you do not
specify a VLAN interface then detailed local
member information is shown for all VLAN
interfaces configured for PIM-SMv6.
Table 4: New and modified commands in 5.4.3
Command Status
x510
x610
x900
x908
x8112
Software
Reference
Chapter Description