Mitsubishi Electronics HC7800DW Projector User Manual


  Open as PDF
of 61
 
EN-5
WARNING:
Unplug immediately if there is something wrong with
your projector.
Do not operate if smoke, strange noise or odor comes out
of your projector. It might cause fire or electric shock. In this
case, unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the User Manual do
not attempt to service this product by yourself. Please
contact your dealer when you want to fix, adjust or
inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged,
unplug the projector and contact your dealer for inspection.
It may lead to fire if you keep using the damaged projector.
Be sure to unplug the power cord from the wall outlet
if the projector is fractured or deformed.
Otherwise, it may result in fire or electric shock. Ask your
dealer for repair.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface only.
Please do not place equipment on unstable surfaces.
Do not look into the lens when it is operating.
It may hurt your eyes. Never let children look into the lens
when it is on.
Do not unplug the power cord during operation.
It can lead to lamp breakage, fire, electric shock or other
trouble. It is best to wait for the fan to turn off before
turning the main power off.
Do not touch the air outlet grille and bottom plate,
which become hot.
Do not touch them or put other equipment in front of
the air outlet grille. The air outlet grille and bottom plate,
when heated, may cause injury or damage to other
equipment. Also, do not set the projector on the desk
which is easily affected by heat.
Do not look into the air outlet grille when projector is
operating.
Heat, dust, etc. may blow out of it and hurt your eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality and fire.
Do not use flammable solvents (benzene, thinner, etc.)
and flammable aerosols near the projector.
Flammable substances may ignite causing fire or
breakdown because the temperature inside the projector
rises very high while the lamp is illuminating.
Do not use the projector with condensation on it.
It can lead to breakdown or other failure.
Place of installation
For safety’s sake, refrain from setting the projector at any
place subjected to high temperature and high humidity.
Please maintain an operating temperature, humidity, and
altitude as specified below.
• Operatingtemperature:between+41°F(+5°C)and
+95°F(+35°C)
• Operatinghumidity:between30%and90%
• Neverputanyheat-producingdeviceunderthe
projector so that the projector does not overheat.
• Donotattachtheprojectortoaplacethatisunstable
or subjected to vibration.
• Donotinstalltheprojectornearanyequipmentthat
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a large
current.
• Placetheprojectoronasolid,vibrationfreesurface;
otherwise it may fall, causing serious injury to a child
or adult, and serious damage to the product.
• Donotstandtheprojector;itmayfall,causingserious
injury and damage to the projector.
• Slantingtheprojectormorethan±10°(rightandleft)or
±15°(frontandrear)maycausetroubleorexplosionof
the lamp.
• Donotplacetheprojectornearair-conditioningunit,
heater, or humidifier to avoid hot or moist air to the
exhaust and ventilation hole of the projector.
• Donotplacetheprojectorinthefollowingplaces.
Otherwise, a short circuit, heat generation, or melting
of the power cord coating may occur, causing fire,
electric shock, product failure, or deformation.
• Outdoorsornonair-conditionedplace
• Placewhereagassuchasahydrogensuldeis
generated (i.e. hot spring)
• Placewherethereistoomuchsaltsuchasnear
the coast
Do not place a container containing water or other
liquid on the projector.
If water spills on or enters the projector, it may result in
fire or electric shock.
Do not put any object that is heavy or larger than the
outer frame on the projector.
Otherwise, the object may fall losing its balance and
cause injury.
Do not subject the projector to strong shocks or
vibrations. Do not handle the projector roughly.
The projector may be damaged, resulting in fire or electric
shock.
Important safeguards (continued)
 previous next