Mitsubishi Electronics HC7800DW Projector User Manual


  Open as PDF
of 61
 
EN-52
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be
sure to unplug the power plug, and then contact your dealer.
No image appears on the screen.
Problem Solution
Power can not be
turned on.
• Checkwhethertheindicatorsareonoroffandhowtheyarelightning.
POWER STATUS Solution
Off Off
• Connectthepowercordtotheprojector.
• Plugthepowercordintoawalloutlet.
Steady red
Off
• Ifanyobjectsareblockingtheairinletoroutletgrill,removethemandcarryoutthe
following.
Unplug the power cord from the wall outlet.1.
Make sure that the projector has cooled off.2.
Plug the power cord into the wall outlet.3.
Press the POWER button.4.
Blinking
orange
• Ifanyobjectsareblockingtheairinletoroutletgrille,removethem.
• Don’texposetheairoutletgrillestohotairemittedfromaheatingappliance.
Blinking
green
• AftertheSTATUSindicatorstopsblinking,pressthePOWERbutton.
If you unplug the power cord while the fan is rotating, the lamp may not turn on about one •
minute when you plug the power cord next time.
The lamp can’t turn on again for one minute after it goes out.•
• PressthePOWERbuttonseveraltimes.
Steady red
• Replacethelamp.(Thelampisattheendofitslife.)
Blinking
red/green
Off
• Attachthelampcover.
Steady
or
Blinking
• Unplugthepowercordfromthewalloutletandcontactyourdealer.
No image appears on
the screen.
• Checkthatthelenscapisremoved.
• Itmaytakeaboutoneminuteforthelamptolightup.
• Thelampfailstolightuponrareoccasions.Insuchacase,waitforafewminutes
and then try again.
• Iftheprojectorwasturnedoffbeforethelampwascooleddownsufcientlylasttime,
the fan may start rotating and the POWER button may not work after the power cord
is plugged. After the fan stops rotating, press the POWER button to turn back on the
POWER indicator.
• Checkthattheintakeventisclean.
• Checkthatthelampcoverisclosed.(Seepage50.)
• Checkthatthecablesconnectedtotheexternaldevicesarenotbroken.
• Whenanextensioncableisbeingused,replaceitwiththesuppliedcableforcheck.
When images are displayed correctly, add an RGB signal amplifier to the extension
cable.
• Checktheoperationmanualofthevideodeviceforitsconnection.
Power turns off. • Thisproblemmayoccurwhentheintakeventand/orexhaustventsareblocked.(In
such a case, the STATUS indicator brinks orange.)
Remove the objects blocking the intake vent and/or exhaust vents and then carry
out the following procedure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator
goes out.)
2. Unplug the power cord from the wall outlet.
3. Wait at least 10 minutes.
4. Plug the power cord into the wall outlet.
5. Press the POWER button.
• WhentheSTATUSindicatorissteadyred,itisindicatingthatthelampshouldbe
replaced. Replace the lamp in this case.
• CheckthatAUTOPOWEROFFhasbeensettoOFF.
• Ifthelamphasdeteriorated,itmaygooutafterawhileitilluminates.
Troubleshooting
 previous next