Filter
Top Products
-62
Specifications
Product type
Model
Video system
Display method
DLP panel
Lens
Projection lamp
Video input signal
S-video input signal
Component input signal
(INPUT 1, 2)
Analog RGB/Digital
(INPUT 5/DIGITAL)
Horizontal resolution
Pixel clock
Vertical frequency
Horizontal frequency
Rated voltage
Input current
Rated frequency
Power consumption
Power consumption (standby)
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
Projector
DT-400
PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480I/480P/720P/1080I
Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
Panel size: 0.8"
Drive method: Digital Light Processing (DLP™)
No. of dots: 921,600 dots (1,280 [H] ן 720 [V])
1–1.5 ן zoom lens, F2.0–2.5 f=21.3–31.6 mm
275 W DC lamp
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
RCA Connector
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB (CB): 0.7 Vp-p, 75 Ω terminated
PR (CR): 0.7 Vp-p, 75 Ω terminated
29-pin DVI-I terminal
<Digital>
Input impedance 50 Ω
Input level 250-1000 mV
<Analog>
Input impedance 75 Ω
Input level 0.7 Vp-p
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB (CB): 0.7 Vp-p, 75 Ω terminated
PR (CR): 0.7 Vp-p, 75 Ω terminated
<Synchronization signal>
••
••
• Separate sync/Composite sync
Input level TTL level
Input impedance 1 KΩ
••
••
• Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75 Ω
720 TV lines (DTV 720P input)
12–80 MHz
43–75 Hz
15–70 kHz
AC 100–240 V
3.65 A (When using AC 100 V)
50/60 Hz
360 W (When using AC 100 V)
6 W (When using AC 100 V)
1,350 BTU/hour
41°F to 95°F (ם5°C to ם35°C)
מ4°F to 140°F (מ20°C to ם60°C)
Plastic
38 kHz
12
7
/32" × 3
33
/64" × 11
7
/64" (310 (W) × 89 (H) × 282 (D) mm)
9.5 lbs. (4.3 kg)
Remote control, Two AA size batteries, Power cord, Lens cap (attached on the body),
Operation manual
Lamp unit (Lamp/cage module) (AN-K2LP), Remote control (RRMCGA334WJSA), AA
size batteries, Power cord (QACCDA007WJPZ), Lens cap (PCAPHA021WJSA),
Operation manual (TINS-B532WJZZ)
As a part of policy of continuous improvement, SHARP reserves the right to make design
and specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
DT400_E_P61_68.p65 04.10.18, 1:26 PM62