Filter
Top Products
Controlling
Controlling
5975696 BARCODATA 2100 140798
8-3
8-3
5975696 BARCODATA 2100 140798
c) Point the front of the RCU directly at one of the IR sensors of the
projector.
When using the wireless remote control, make sure you are within
the effective operating distance (30m (100ft) in a straight line). The
remote control unit will not function properly if strong light strikes the
sensor window or if there are obstacles between the remote control
unit and the projector IR sensor.
Projector Address
a. Software Set Up of the Projector Address.
See 'Change projector address' in chapter 'Service mode'.
Every projector requires an individual address between 0 and 255
which can be set in the Service mode.
Only projectors with addresses between 0 and 9 can be
controlled with the RCU.
b. How to Control the Projector or Projectors.
The projector's address may be set to any value between 0 and 255.
When the address is set, the projector can be controlled now :
- RCU for addresses between 0 and 9.
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for
addresses between 0 and 255.
Note : a projector will respond to a RCU set to an address of '0'
regardless of what address is set in the projector itself.
c. Using the RCU.
Before using the RCU, its is necessary to enter the projector address
into the RCU (only when that address is between 1 and 9). The
projector with the corresponding address will listen to that specific
RCU.
When address 0, 'zero address' is programmed into the RCU, every
projector, without exception will listen to the commands given by this
RCU.
ADDR
ADJ EXIT
STBYMUTETEXT
BRIGHTNESS
-
+
-
+
-
+
-
+
SHARPNESS
-
+
TINT
COLOR
CONTRAST
10
9
78
65
43
21
RCU
Front of projector
RCU
Rear of projector
IR sensor
Table
45°
45°
45°
45°
0I
SOURCE 1
SOURCE 4
SOURCE 5
SOUR CE 2
SOUR CE 3
AUDIO OUT
AUDIO IN C
AUDI O IN BAUDIO IN A
VID EO
VIDEO
S VIDEO
RGBH/CV
RGBH/CV
L - R L - R L - R L - R
IR
RR
GG
B
B
H/C H/C
VV
RS 232 IN
RS 232 OUT
COMM PORT
CTRL
hard wired
remote
Read instructions before
connecting peripherals
ADDR
ADJ EXIT
STBYMUTETEXT
BRIGHTNESS
-
+
-
+
-
+
-+
SHARPNESS
-
+
TINT
COLOR
CONTRAST
109
7
8
65
43
21
c) Point the front of the RCU directly at one of the IR sensors of the
projector.
When using the wireless remote control, make sure you are within
the effective operating distance (30m (100ft) in a straight line). The
remote control unit will not function properly if strong light strikes the
sensor window or if there are obstacles between the remote control
unit and the projector IR sensor.
Projector Address
a. Software Set Up of the Projector Address.
See 'Change projector address' in chapter 'Service mode'.
Every projector requires an individual address between 0 and 255
which can be set in the Service mode.
Only projectors with addresses between 0 and 9 can be
controlled with the RCU.
b. How to Control the Projector or Projectors.
The projector's address may be set to any value between 0 and 255.
When the address is set, the projector can be controlled now :
- RCU for addresses between 0 and 9.
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for
addresses between 0 and 255.
Note : a projector will respond to a RCU set to an address of '0'
regardless of what address is set in the projector itself.
c. Using the RCU.
Before using the RCU, its is necessary to enter the projector address
into the RCU (only when that address is between 1 and 9). The
projector with the corresponding address will listen to that specific
RCU.
When address 0, 'zero address' is programmed into the RCU, every
projector, without exception will listen to the commands given by this
RCU.
ADDR
ADJ EXIT
STBYMUTETEXT
BRIGHTNESS
-
+
-
+
-
+
-
+
SHARPNESS
-
+
TINT
COLOR
CONTRAST
109
78
65
43
21
RCU
Front of projector
RCU
Rear of projector
IR sensor
Table
45°
45°
45°
45°
0I
SOURCE 1SOURCE 4SOURCE 5
SOUR CE 2
SOUR CE 3
AUDIO OUT
AUDIO IN C
AU DI O IN BAUD IO IN A
VID EO
VIDEO
S VIDEO
RGBH/CVRGBH/CV
L - R L - R L - R L - R
IR
RR
GG
B
B
H/C H/C
VV
RS 232 IN
RS 232 OUT
COMM PORT
CTRL
hard wired
remote
Read instructions before
connecting peripherals
ADDR
ADJ EXIT
STBYMUTETEXT
BRIGHTNESS
-
+
-
+
-
+
-+
SHARPNESS
-
+
TINT
COLOR
CONTRAST
109
78
65
43
21