Filter
Top Products
4-4
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
Chapter 4 Installing and Removing a Cisco 7600 Series Ethernet Services Plus Line Card
Online Insertion and Removal
Reactivating a Cisco 7600 Series Ethernet Services Plus Line Card
Once you deactivate a Cisco 7600 Series ES+ line card, whether or not you have performed an OIR, you
must use the power enable module global configuration command to reactivate the Cisco 7600 Series
ES+ line card.
If you did not issue a command to deactivate the SFP or XFP modules installed in a Cisco 7600 Series
ES+ line card, but you did deactivate the Cisco 7600 Series ES+ line card using the no power enable
module command, then you do not need to reactivate the SFP or XFP modules after an OIR of the Cisco
7600 Series ES+ line card. The installed SFP or XFP modules automatically reactivate upon reactivation
of the Cisco 7600 Series ES+ line card in the router.
For example, consider the case where you remove a Cisco 7600 Series ES+ line card from the router to
replace it with another Cisco 7600 Series ES+ line card. You reinstall the same SFP or XFP modules into
the new Cisco 7600 Series ES+ line card. When you enter the power enable module command on the
router, the SFP or XFP modules will automatically reactivate with the new Cisco 7600 Series ES+ line
card.
To activate a Cisco 7600 Series ES+ line card and its installed SFP or XFP modules after the Cisco 7600
Series ES+ line card has been deactivated, use the following command in global configuration mode:
For more information about chassis slot numbering, refer to the Identifying Slots and Subslots for the
Cisco 7600 Cisco 7600 Series ES+ Line Cards, page 2-3 section in this guide.
Verifying Deactivation and Activation of a Cisco 7600 Series Ethernet Services
Plus Line Card
To verify the deactivation of a 7600 ES+ line card, enter the show module command in privileged EXEC
configuration mode. Observe the Status field associated with the 7600 ES+ line card that you want to
verify.
The following example shows 7600 ES+ line cards located in slots 4 and 6. Slot 6 is powered down. This
is indicated by its “PwrDown” status.
Router# show module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL0930696R
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL0929634V
3 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAB09270AEQ
4 40 7600 ES+ 7600-ES+40G3CXL JAE1146355M
5 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAD085106Z7
6 4 7600 ES+ 7600-ES+4TG3C JAE11518648
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0014.f212.0028 to 0014.f212.003f 2.2 12.2(14r)S5 12.2(nightly Ok
2 0014.f211.f20c to 0014.f211.f23b 2.2 12.2(14r)S5 12.2(nightly Ok
Command Purpose
Router(config)# power enable module slot Activates the ES+ line card in the specified slot and its
installed SFPs or XFPs, where:
• slot—Specifies the chassis slot number where the
ES+ line card is installed.