Filter
Top Products
HP OmniBook XE2 Troubleshooting and Diagnostics 3-15
0603h For the external loop-back test, make sure the
loop-back connector is installed and
constructed properly. For the external or
internal loop-back test, replace the
motherboard.
0604h -
0605h
Replace the motherboard.
0606h For the external loop-back test, make sure the
loop-back connector is installed and
constructed properly. For the external or
internal loop-back test, replace the
motherboard.
0607h Make sure the loop-back connector is installed
and constructed properly. Replace the
motherboard.
0608h -
0617h
Replace the motherboard.
Parallel Port Tests
0701h For the external loop-back test, make sure the
loop-back connector is installed and
constructed properly. For the external or
internal loop-back test, replace the
motherboard.
0702h Replace the motherboard.
0703h Run BIOS Setup and disable ECP for the
parallel port, then rerun the test. Replace the
motherboard.
0704h -
0706h
Replace the motherboard.
0707h Connect the loop-back connector.
0708h Replace the motherboard.
Audio Tests
0801h -
0816h
If this error also occurs for an external
headphone, replace the motherboard (or VGA
PCA for the OB 4150). Otherwise, check the
speaker connections, replace the speakers. If it
occurs only for an external headphone, replace
the audio jack PCA.
9003h -
9004h
(See Microphone Tests near end of table.)
Video Tests
0900h -
0901h
Replace the VGA PCA.
0903h -
0906h
Replace the LVDS PCA. Replace the VGA
PCA.
0907h -
0908h
Replace the VGA PCA.
0909h -
090Ah
Replace the LVDS PCA. Replace the VGA
PCA.
090Ch -
090Fh
Replace the VGA PCA.
0920h Replace the LVDS PCA. Replace the VGA
PCA.
8000h (See LCD Test near end of table.)
CD-ROM Tests
0A00h Insert a CD in the drive.
0A01h Rerun the test. Replace the CD-ROM drive.
0A02h No repair. (Automatic close not supported.)
0A03h Insert a different CD in the drive. Check the
connectors on the CD-ROM drive and
motherboard. Replace the CD-ROM drive.
0A04h Insert a computer CD in the drive.
0A05h Insert a different CD in the drive. Check the
connectors on the CD-ROM drive and
motherboard. Replace the CD-ROM drive.
0A06h Insert an audio CD in the drive.
SMBus Tests
0E00h -
0E10h
Replace the motherboard.
ATAPI Removable Tests (LS-120)
0F02h -
0F03h
Rerun the test. Insert a different disk in the LS-
120 drive. Check the connectors on the LS-120
drive and motherboard. Replace the LS-120
drive.
0F04h -
0F05h
Replace the LS-120 drive.
TI CardBus Tests
1201h Memory space not available. Remove any
attached ISA or PCI cards.
1202h -
1203h
Replace the motherboard.
1205h -
1206h
Insert a different PC Card. Replace the
PCMCIA socket. Replace the motherboard.
USB Tests
1301h Reprogram the BIOS IC. Replace the BIOS IC.
Replace the motherboard.
1302h -
1312h
Replace the motherboard.
9006h (See USB Port Test near end of table.)
LCD Test
8000h If the test fails with an external monitor (must
support VESA mode 105h), replace the VGA
PCA, replace the motherboard. Otherwise:
- If the shaded-band test fails, check the LCD
flex cable connection in the bottom case,
replace the LVDS PCA, replace the LCD flex
cable, replace the VGA PCA, replace the
motherboard.
- If only a solid-color test fails, see chapter 5 for
cosmetic guidelines, replace the LCD module.
Microphone/Line-In Tests
9003h If the error occurs for built-in and external
microphones, replace the motherboard (or VGA
PCA for the OB 4150). If it occurs for only the
built-in microphone, check the LCD flex cable
connection, replace the inverter PCA. If it
occurs only for an external microphone, replace
the audio jack PCA.
9004h Replace the audio jack PCA. Replace the
motherboard (or VGA PCA for the OB 4150).
Suspend/Resume Test
9005h Run BIOS Setup and restore default settings.
Reprogram the BIOS IC. Replace the BIOS IC.
Replace the motherboard.
USB Port Test
9006h Make sure a USB device is connected to the
port you are testing. Select the correct speed
for the device. Replace the motherboard (or
dock component, if applicable).