Filter
Top Products
Contents 7
Drive Time-Out Occurred on Physical Drive Bay X.............................................................................. 80
Drive X Indicates Position Y............................................................................................................. 80
Duplicate Write Memory Error ........................................................................................................ 80
Error Occurred Reading RIS Copy from SCSI Port X Drive ID............................................................... 80
FYI: Drive (Bay) X is Third-Party Supplied .......................................................................................... 80
Identify Logical Drive Data did not Match with NVRAM...................................................................... 81
Insufficient adapter resources .......................................................................................................... 81
Inter-Controller Link Connection Could Not Be Established .................................................................. 81
Less Than 75% Batteries at Sufficient Voltage .................................................................................... 81
Less Than 75% of Batteries at Sufficient Voltage Battery Pack X Below Reference Voltage........................ 81
Logical Drive X Failed Due to Cache Error ........................................................................................ 81
Logical Drive X Status = Failed ........................................................................................................ 81
Logical Drive X Status = Interim Recovery (Volume Functional, but not Fault Tolerant) ..............................82
Logical Drive X Status = Loose Cable Detected... ............................................................................... 82
Logical Drive X Status = Overheated ................................................................................................ 82
Logical Drive X Status = Overheating ............................................................................................... 82
Logical Drive X Status = Recovering (rebuilding data on a replaced drive) ............................................ 82
Logical Drive X Status = Wrong Drive Replaced ................................................................................ 83
Loose Cable Detected - Logical Drives May Be Marked FAILED Until Corrected...................................... 83
Mirror Data Miscompare................................................................................................................ 83
No Configuration for Array Accelerator Board.................................................................................. 83
One or More Drives is Unable to Support Redundant Controller Operation ........................................... 83
Other Controller Indicates Different Hardware Model.........................................................................83
Other Controller Indicates Different Firmware Version......................................................................... 84
Other Controller Indicates Different Cache Size.................................................................................84
Processor Reduced Power Mode Enabled in RBSU ............................................................................. 84
Processor Not Started (Processor Stalled).......................................................................................... 84
Processor Not Started (Stepping Does Not Match) ............................................................................. 84
Processor Not Started (Unsupported Processor Stepping) .................................................................... 84
Processor Not Supported (Unsupported Core Speed) ......................................................................... 84
RIS Copies Between Drives Do Not Match ........................................................................................ 84
SCSI Port X Drive ID Y Failed - REPLACE (failure message) .................................................................. 85
SCSI Port X, Drive ID Y Firmware Needs Upgrading .......................................................................... 85
SCSI Port X, Drive ID Y Has Exceeded the Following Threshold(s)......................................................... 85
SCSI Port X, Drive ID Y is not Stamped for Monitoring........................................................................ 85
SCSI Port X, Drive ID Y May Have a Loose Connection....................................................................... 85
SCSI Port X, Drive ID Y RIS Copies Within This Drive Do Not Match..................................................... 85
SCSI Port X, Drive ID Y...S.M.A.R.T. Predictive Failure Errors Have Been Detected in the Factory Monitor and
Performance Data.......................................................................................................................... 85
SCSI Port X, Drive ID Y...S.M.A.R.T. Predictive Failure Errors Have Been Detected in the Power Monitor and
Performance Data.......................................................................................................................... 86
SCSI Port X, Drive ID Y Was Replaced On a Good Volume: (failure message)....................................... 86
Set Configuration Command Issued ................................................................................................. 86
Soft firmware upgrade required....................................................................................................... 86
Storage Enclosure on SCSI Bus X has a Cabling Error (Bus Disabled)... ................................................ 86
Storage Enclosure on SCSI Bus X Indicated a Door Alert..................................................................... 86
Storage Enclosure on SCSI Bus X Indicated a Power Supply Failure...................................................... 86
Storage Enclosure on SCSI Bus X Indicated an Overheated Condition... ............................................... 87
Storage enclosure on SCSI Bus X is unsupported with its current firmware version... ............................... 87
Storage Enclosure on SCSI Bus X Indicated that the Fan Failed... ......................................................... 87
Storage Enclosure on SCSI Bus X Indicated that the Fan is Degraded... ................................................ 87
Storage Enclosure on SCSI Bus X Indicated that the Fan Module is Unplugged... ................................... 87
Storage Enclosure on SCSI Bus X - Wide SCSI Transfer Failed............................................................. 87
Swapped cables or configuration error detected. A configured array of drives... ...................................88