Filter
Top Products
4.9 Telnet Setup (continued)
In the Configuration mode you can make any changes just like you would do using the Web
Browser. After connected to the iServer, the user can use the following commands to read, modify,
and get help from the iServer console.
? Following with a return character, the console will show all the commands and options (Figure 4.17).
p Following with a return character, the console will show the iServer configurations (Figure 4.16).
s Is the configuration command, used to set a new setting (see the example in Figure 4.17)
r This command is used to read the status of the digital I/O signals (0 is low and 1 is high)
Example: r DCD response will be DCD (DSR)=0
r DTR response will be DTR=0
w This command is used to change the status of the digital I/O signals (applies only to the
outgoing signals, DTR and RTS)
Example : w RTS=1 means raise the RTS
w DTR=0 means lower the DTR
RESET following with a return character, it will recycle the Power on the iServer.
FACTORY following with a return character, it will set the iServer to it’s factory default settings.
Figure 4.17 Telnet Setup - iServer Help Page
Admin. Password:00000000
Admin. Login Successful
iServer Configuration Command:
?
cc description pppppp
BD BaudRate 0-300,1-600,2-1200,3-2400,4-4800,5-9600,6-19200,
7-38400, 8-57600, 9-115200
PT Parity 0-none,1-Odd,2-even
ST StopBits 0-1bits,1-2bits
DT DataBits 0-7bits,1-8bits
FC FlowControl 0-none,1-XON/XOFF,2-Hardware
MD Mode 0-RS232, 1-RS485
MB Modbus/TCP 0-disable, 1-enable
TO TimeOut xxxx ms Rang range 100-9999
TU TCP/UDP 0-TCP, 1-UDP
TT TerminalType 0-Host, 1-Slave
TN TerminalNumber 0-5
PP TerminalPort XXXXX 500-65535 but 1000 and 2002
HN HostName XXXXXXXX maxim 18 characters
IP Static IP XXX.XXX.XXX.XXX
LP Login Password XXXXXX maxim 16 characters
SP Admin Password XXXXXX maxim 16 characters
TP Device Type 0-iServer,1-iDRN,2-iDRX,3-iSeries,4-iNFB,5-iLD
RE Remote Enable 0-Disable, 1-Enable
RI Remote IP XXX.XXX.XXX.XXX
RP Remote Port XXXXX 500-65535 but 1000 and 2002
GW Gateway XXX.XXX.XXX.XXX
EC End Char XX represents the Hex Num. of ASCII. i.e 0D means CR
(Carrige Return)
FE Forward End Char 0-disabled, 1-enabled
EP Enable Serial Port Password 0-disabled, 1-enabled
CP Serial Port Password XXXXXX maxim 16 characters
CC Connect CTRL 0-not used,1-RTS+,2-RTS-,3-CTS+,4-CTS_,5-RTS-CTS+,
6-RTS-CTS-, 7-DTS+,8-DTR-, 9-DCD/DSR+,
A-DCD/DSR-, B-DTR-DCD+, C-DTR-DCD-, D-RECONNECT
CT Connect Timeout XXXXX 1-65535
WB Web Server 0-disable, 1-enable
Example:
To configure Baudrate 9600, 1 stop bit, Odd Parity, and RS232 mode.
s -BD5 -PT1 -ST1 -MD0
27