Filter
Top Products
26
RQT8739
Enjoying the Home Theater
Digital signals this unit can play:
Dolby Digital (including Dolby Digital Surround EX), DTS (including DTS-ES and DTS 96/24) and PCM (á page 39)
• The unit memorizes whether [SURROUND] has been pressed
on or off for each input source.
•
The setting always switches from off to on when the input comes
from a surround source in Dolby Digital, DTS or other formats.
• When you press [SURROUND] off while playing a surround
source (excluding a DVD-Audio source that does not allow
down-mixing), 2-channel mix (2CH MIX) activates.
2-channel mix is canceled when you turn the unit off or when
you switch input sources.
• The “SURROUND” indicator goes off when the sampling
frequency for the input signal is higher than 96 kHz.
• The number of source channels appears on the display when
a digital signal is input or input sources are switched. (Their
number may not appear depending on the selected source.)
• The unit is compatible with linear PCM 8-channel surround
signals decoded by the BD player and other equipment (up to
96 kHz/24 bit). See the operating instructions for equipment
used for playback.
RECEIVER
AV
SYSTEM
TV
RECORDER
DVD
BD/DVD
PLAYER
ANALOG 6CH
VCRCD
TUNER
BAND
CH
SPEAKERS
W
-MENU/
-
SETUP
ENTER
INPUT SELECTOR VOLUME
BI-AMP
SURROUND
SURROUND
SPEAKERS
AUTO DETECTOR
-
MULTI ROOM
TUNE
AUX
ADVANCED DUAL AMP
POWER
WIRELESS READY
AUTO SPEAKER SETUP
SETUP MIC
HDMI
MULTI ROOM
RETURN
SURROUND
SPEAKERS
ENTER
-
MENU/
-
SETUP
AUTO DETECTOR
-
MULTI ROOM
RETURN
TUNE
SETUP MIC
W
AUX
S VIDEO
VIDEO
L
-
AUDIO
-
R
POWER
“SURROUND”
“BI-AMP” “MULTI ROOM”
“ADVANCED DUAL AMP”
INPUT SELECTOR
A
B
SPEAKERS
SURROUND
VOLUME
“ ”
1
To turn the unit on
Press
The “SURROUND” indicator lights on (factory
setting).
• The standby indicator “^” goes off when you turn the unit on.
Do not forget to perform speaker detection when you play
a source with the unit for the first time or when you change
the number of connected speakers (á pages 10 and 24).
2
To select “SPEAKERS A”
Press to switch “ ” on.
To select “SPEAKERS B”
Press [SPEAKERS B].
(
á
page 27)
To use bi-wire speakers (á page 20)
To enjoy BI-AMP stereo sounds
See page 27.
Press [SPEAKERS A] or [SPEAKERS B] to switch
“” on.
3
To switch input sources
• Select the connected terminal when the names of the
terminal and equipment you wish to use for playback
do not match.
Turn
• When you select “DVR
”, “DVD RECORDER
” scrolls across
the display once.
•
Y
ou can also select an input source using the remote control (
á
page 5).
To use a DVD recorder with built-in VCR (
á
page 17)
• To play a DVD: select “DVR
”
• To play a video cassette: select “VCR
”
4
Play the selected input source.
To switch between 2-channel
stereo playback and surround
playback
Press [SURROUND].
5
To adjust the volume
Turn
Volume range:
– – dB (minimum),
–79dB to 0dB (maximum)
To finish the Home Theater
Be sure to reduce the volume and press [8, POWER] to turn the unit to standby.
8
POWER
Note
A
SPEAKERS
A
A
SPEAKERS
A B
A B
SPEAKERS
BI-WIRE
INPUT SELECTOR
(
e.g.
)
AUX
CD
TV/STBBD/DVDDVRVCR
TUNER XMTUNER AMTUNER FM
VOLUME
Note
Subwoofer
Number of surround and surround back channels
Number of front and center channels