Filter
Top Products
35
RQT8739
Setting speakers and
their sizes
• You can set connected
speakers and their sizes
manually.
• Different ranges are played
by different speakers. Size
setting is necessary for
reproducing sources,
particularly their bass
section, completely.
1 Select and confirm the choice.
2 Select a speaker for setting and
confirm the choice.
3 Change a setting and confirm the
choice.
To go back to step 1
Select and confirm the choice.
When you set the front speakers (LR) as “LARGE ”
• The subwoofer also makes audio output in the
bass range when you perform stereo playback
of analog and PCM sources.
• The subwoofer sends out only the LFE (low
frequency effect channel) signal contained in
2-channel Dolby Digital or DTS sources when
you play them in stereo.
SUBW :Subwoofer
LR : Front speakers
C : Center speaker
S : Surround speakers
SB : Surround back speakers
SUBW : NO ; unconnected YES ; connected
LR, C, S :
NONE ;
For speakers you haven’t connected (center or
surround only).
SMALL ;
For speakers that cannot adequately
reproduce the bass range. This setting is
sufficient for most speakers if you are using a
subwoofer.
LARGE ;
For speakers that can sufficiently reproduce
the bass range down to 20 Hz.
SB :
NONE ;
For speakers you haven’t connected.
1-SPK ;
If you connect one surround back speaker.
2-SPK ;
If you connect two surround back speakers.
Factory settings: LR, C, S ; SMALL
SUBW ; YES
SB ; 2-SPK
• Set the lowpass filter frequency according to frequencies available for playback when speakers
are set as “SMALL ”. The factory setting is 80 Hz. (below)
• The following are set automatically.
When you set “LR
” to “SMALL
”, “SUBW
” is set to “YES
”.
When you set “SUBW ” to “NO ”, “LR
” is set to “LARGE
”.
•“SB ” does not appear when “S ” is set to “NONE ”.
• The “SB
” size becomes the “S
” size because the unit does not offer “SB
” size setting.
• When you change the number of connected speakers, settings made with the setup microphone
are canceled. (á pages 24 and 25)
Setting distances
• By adjusting the distance
from each speaker (except
the subwoofer) to the
seating area, the sound
delay time is automatically
adjusted so that sound
reaches the listener at the
same time.
1 Select and confirm the choice.
2 Select a speaker for setting and
confirm the choice.
3 Select a distance and confirm the
choice.
L : Front left C : Center
R : Front right LS : Surround left
RS : Surround right
SBL : Surround back left
SBR : Surround back right
Adjustment range: 1.0 to 45.0 ft (feet)
This unit is adjusted at 0.5 feet intervals.
Factory settings: L, R ; 10.0 ft (feet)
C ; 10.0 ft (feet)
LS, RS ; 5.0 ft (feet)
SBL, SBR ; 5.0 ft (feet)
• Speakers whose polarity was automatically adjusted through the auto speaker setup using the
setup microphone are displayed with “– ” such as “L 10.0 – ”.
• When the speaker distance measured through the auto speaker setup (á pages 24 and 25)
exceeds 45 feet (15 meters), the distance is displayed as “OVER ”.
Setting the lowpass
filter
• If the speaker sizes (above)
are set to “SMALL”, make
this setting.
• The unit cannot reproduce the
entire bass range when speakers
are set as “SMALL ”. You can
arrange the unit to provide missing
bass sounds through the
subwoofer by setting the lowpass
filter frequency according to
frequencies available for playback.
1 Select and confirm the choice.
2 Select the lowpass filter frequency
and confirm the choice.
Lowpass filter frequency for sending the bass
range to the subwoofer:
80, 100, 120, 140, 160, 180, 200 (Hz)
Factory setting: 80 (Hz)
The setting made through these steps applies to all speakers set as “SMALL
”.
Note
ft
ft
Note
Note
Settings
Operations