Filter
Top Products
Positioning the projector and screen
• Place the projector on a stable, level surface, out of direct
sunlight and away from sources of excessive dust, dirt, heat,
water, moisture, vibration and strong magnetic fields.
Face the projector towards the screen for the best picture
results. To determine the distance for the desired size,
please refer to the Projection Assistant, a calculation
programme included on the CD-ROM.
• The screen should be positioned so that it is not directly
touched by sunlight or artificial light, as this will wash out the
colours of the picture, making it hard to see.
• The projector can be used for both front projection, rear
projection and ceiling projection applications. As default
factory setting, the projector has been set up for front
projection. You can change to rear or ceiling projection via the
OSD menu. See ‘Rear screen projection’ and ‘Ceiling-mount
projection’ under ‘Operation - Display and picture control’ for
further instructions.
• Choose a screen size suitable for the number of viewers and
the size of the room.
• Picture quality is best when you sit directly in front of the
projector screen.
Mains supply
1.
Insert the mains lead into the projectors POWER socket and
connect it to the wall socket.
Note: The standby indicator lights up red, the projector is now in
the Power/Standby mode.
2.
Remove the lens cap.
3.
Press the STANDBY ON/OFF button to switch on the
projector.
– The lamp indicator
flashes green and the
start-up screen appears
for 5 seconds.
– When the projection
lamp is on, the lamp
indicator lights up green.
4.
To switch off the mains supply completely, pull the mains
plug out of the wall socket.
Note: Before disconnecting the mains lead, make sure that the
cooling fan has stopped (about 3 minutes after the
projector has been switched to Power Standby).
Adjusting the focus and size of the image
• Use the ZOOM ring to adjust the size of the image.
• Use the FOCUS ring to adjust the focus of the image.
Adjusting the vertical and horizontal angle of the projector
Vertical angle
• Use the Height/Level Adjuster to adjust the vertical angle of
the projector as specified under ‘Positioning the projector and
screen’.
To Raise: press the adjuster carefully and lift to raise the
projector.
To Lower: press the adjuster carefully again to lower the
projector.
• Use the FOCUS Ring and ZOOM Ring to readjust the focus
and size of the image.
O
K
M
e
n
u
D
a
t
a
L
a
m
p
M
u
t
e
A
V
M
u
t
e
R
C
V
o
lu
m
e
S
t
a
n
d
b
y
Video
O
n
/
O
f
f
O
K
M
e
n
u
D
a
t
a
L
a
m
p
M
u
t
e
A
V
M
u
t
e
R
C
V
o
l
u
m
e
S
t
a
n
d
b
y
Video
O
n
/
O
f
f
D
a
ta in
S
-V
id
e
o in
V
id
e
o
in
A
u
d
io
A
u
d
io
o
u
t
A
u
d
io
o
u
t
L
R
D
a
ta
in
S
-
V
id
e
o
in
V
id
e
o
in
A
u
d
io
L
R
P
o
w
e
r
Data
A
u
d
io
Video
U
S
B
in
U
S
B
in
U
S
B
o
u
t
U
S
B
o
u
t
Focus ring
Zoom ring
O
K
M
e
n
u
D
a
t
a
L
a
m
p
M
u
t
e
A
V
M
u
t
e
R
C
V
o
l
u
m
e
S
t
a
n
d
b
y
Video
O
n
/
O
f
f
O
K
M
e
n
u
D
a
t
a
L
a
m
p
M
u
t
e
A
V
M
u
t
e
R
C
V
o
l
u
m
e
S
t
a
n
d
b
y
Video
O
n
/
O
f
f
D
a
t
a
in
S
-V
id
e
o
in
V
id
e
o
in
A
u
d
io
A
u
d
io
o
u
t
A
u
d
io
o
u
t
L
R
D
a
t
a
in
S
-
V
id
e
o
in
V
id
e
o
in
A
u
d
io
L
R
P
o
w
e
r
D
ata
A
u
d
io
Video
U
S
B
in
U
S
B
in
U
S
B
o
u
t
U
S
B
o
u
t
Data in
S-Video in Video in Audio
Audio
LR
Data in
S-Video in Video in Audio
Audio
LR
Power
Data
AudioVideo
out
out
USB in USB out
USB in USB out
6. Set Up
8
Multimedia projectors
PHILIPS