Filter
Top Products
RESTRICTED USE ONLY Fargo Electronics, Inc.
Persona C30 Card Printer User Guide (Rev. 2.2)
15-2
Disables Magnetic Verification, 4-53
disk cleanup utility, 4-3
Dither, 14-5
DMA (Direct Memory Access), 14-3
Dongle, 14-5
Dot, 14-5
Dot pitch, 14-5
Download, 14-5
DPI (Dot Per Inch), 14-5
DRAM (Dynamic Random Access Memory), 14-5
Driver, 14-5
DTC400/DTC300/DTC300M Card Printer, 7-1
Duplex Printing, 14-5
Dwell Time, 14-6
Dye Migration, 14-6
Dye-Sub Intensity setting, 4-43
Dye-Sublimation, 2-5, 14-6
Dye-Sublimation Cyan Panel, 2-7
Dye-Sublimation Magenta Panel, 2-7
Dye-Sublimation Yellow Panel, 2-7
Dye-Sublimation-Only Print Ribbons, 2-9
E
E-card, 14-6
E-card Docking Station, 14-6
ECP Mode (Enhanced Capabilities Port Mode), 14-6
Edge-to-Edge, 14-6
EE Memory, 14-6
EEPROM (Electrically Erasable Programmable Read
Only Memory), 14-6
embedded contaminants, 2-11, 4-40
Emissions Standards, 2-2
Enable MLE Support checkbox, 5-43
Encoder (smart card), 14-6
Encoder (wheel), 14-7
End Sentinel (ES)., 5-48
Engine, 14-7
EOF (End Of Form), 14-7
EPP (Enhanced Parallel Port), 14-7
EPROM (Electronically Programmable Read Only
Memory), 14-7
EPROM version number, 4-52, 4-54
Escape sequence, 14-7
ESD, 1-2, 5-4, 6-1, 9-1
ESD (ElectroStatic Discharge), 14-7
Ethernet, 14-7
excessive resin printing problems, 4-46
exposed to static electrical discharges, 6-2
F
Fargo Technical Support, 12-1
Fargo Technical Support via the Web, 12-1
FCC, 2-1
feed card into encoder, 4-3
Field Separator (FS), 5-48
Film, 14-7
Firmware, 14-7
Flash Memory, 14-8
Flipper Table Module, 2-12
Font, 14-8
For Overlay Only, 5-57
For Print and Overlay, 5-57
FPGA (Field Programmable Gate Array), 14-8
Front and Back radio buttons, 2-12
Front Cover, 2-6
Frontside and Backside options
K Panel Resin, 5-74, 5-75, 5-76
Overlay / Print Area, 5-52
Full bleed, 14-8
Full Card option, 5-55, 5-78
G
Gamma, 14-8
Glossy / Matte, 14-8
Glossy PVC, 14-8
Graphical Device Interface (GDI), 14-8
Gray Scale, 14-8
H
Halftoning, 14-8
Hard Drive, 14-9
hard Drive space
adequate or inadequate, 4-3
HDP (High Definition Printing™), 14-9
Head, 14-9
Headlift Motors, 4-31
Headlift Sensors, 4-31
Heat Seal, 14-9
Heat sink, 14-9
HiCo (High Coercivity), 14-9
high-resolution, 24-bit color images, 4-51
Horizontal adjustment, 5-34
HTML (HyperText Markup Language), 14-9
HTTP (HyperText Transfer Protocol), 14-9
Humidity, 2-3
I
IC (Integrated Circuit), 14-9
ID (Identification), 14-9
ID format, 5-22
Identification Card sample, 5-82
IEEE 1284 (Institute of Electrical and Electronics
Engineers 1284), 14-10
Image, 14-10
Image Color tab, 5-20, 5-28
Image Darkness option, 5-93
Image Placement, 4-49, 4-50
Image Placement option, 5-94
image placement problems, 4-49
Image Placement value, 5-94
Image Position controls, 5-33
inches or mm option, 5-6
incorrect image darkness problems, 4-42
increase Printhead heat, 5-93
Input, 14-10
Input Hopper, 14-10
Interface, 2-3
Intermediate Transfer Media (InTM), 14-10
internal Printer settings, 5-32