Mitsumi electronic WD3300U Projector User Manual


  Open as PDF
of 52
 
EN-17
Viewing computer images (continued)
9. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
10. Adjust with the or button to get an approximate size.
• WhentheENTERbuttonispressedwhiletheZOOM/FOCUSmenuisdisplayed,theadjustmentmodeis
switched between FAST and STEP. When FAST is selected, the speed of zoom controlled by the or
button becomes fast, and it becomes slow when STEP is selected.
11. Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen.
12.Press the or button to adjust the vertical position and or button to adjust the horizontal position of the
displayed image.
• Whentheimageisnotdisplayedwithinthescreen,adjusttheprojectionangle.Inaddition,performthe
keystone adjustment, if necessary. (See page 11.)
Repeat steps 4, 5 and 9 to 12, if necessary.
Important:
• Focus,zoomandlensshiftadjustmentispossibleinthenormalpicturemodeonly.
To stop projecting:
13. Press the POWER button.
• Aconrmationmessageisdisplayed.
• Tocanceltheprocedure,leavetheprojectorforawhileorpressanybuttonexceptthePOWERbutton.
14. Press the POWER button again.
• Thelampgoesoutandtheprojectorgoesintoastandbymode.Inthisstandbymode,theSTATUSindicator
blinks green.
15. Wait about 2 minutes for the STATUS indicator to be turned off.
• Duringthisperiodof2minutesinthestandbymode,theintakefanandexhaustfanrotatetocoolthelamp.
• Theairoutletfansrotatefasterasthetemperaturearoundtheprojectorrises.
• Thoughthefansmakeloudsoundsduringcooling,suchsymptomisnotamalfunction.
16. Turn off the main power switch.
• ThePOWERindicatorwillgoout.
• Ifthemainpowerswitchshouldbeturnedofforthepowercordshouldbeunpluggedaccidentallywhileeither
the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10
minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn’t light up
immediately, repeat pressing the POWER button 2 or 3 times. If it should still fail to light up, replace the lamp.
• Coverthelenswiththelenscaptoprotectitfromdust.
• Forsafety’ssake,unplugthepowercordfromtheoutlet.
• Whenyourepeatturningoffthemainswitchwithin30minutesfromthelampillumination,anerrormayoccur
in the clock function of this product.
Instant Shut Down
You can turn off this projector just by turning off the power switch or unplugging the power cord without pressing the
POWER button.
• Don’tshutdowntheprojectorwhiletheSTATUSindicatorisblinkingafterthelamplightsupbecausethelamp’s
life may be shortened.
• Don’tturntheprojectorbackonrightaftershuttingitdownbecausethelamp'slifemaybeshortened.(Waitabout
10 minutes before turning the projector back on.)
• Beforeshuttingdowntheprojector,besuretoclosethemenuscreen.Ifyoushutdowntheprojectorwithout
closing the menu, the setting data of the menu may not be saved.
• Ifyoushutdowntheprojectorwhilecontrollingtheprojectorusingthenetworkfunction,theapplicationsoftware
such as ProjectorView may fail. For details, see “User Guide of LAN Control Utility” contained in the CD-ROM.
 previous next