Filter
Top Products
B83F Installation Manual
<Parts included>
1. Turn off the main switch of the main unit of the printer.
2. Remove the upper cabinet of the stand/paper drawer.
<1> Pull out the tray of the
stand/paper drawer.
Remove the four screws
attached to the right on the top of
the stand/paper drawer and
remove the cabinet.
Turn the main switch located on the front side of the
main unit to the "OFF" position.
Then, remove the power plug of the main unit from
the outlet.
12.
<2> Mount screw B to the
position shown in the
illustration.
3. Attach the finisher.
<1> Remove the paper exit
actuator from the main unit of
the printer.
<2> Raise the relay unit at the
side of the finisher.
<3> Hold the grip of the finisher
and place the finisher on the
stand/paper drawer temporarily.
Then, push the lower part to
attach the finisher by sliding it
toward the exit tray of the main
unit.
At this time, align the finisher with
the exterior line of the
stand/paper drawer.
6. Process the AC inlet cover attached to the rear cabinet
of the stand/paper drawer.
<1> Remove the screw that fixes
the harness cover of the main
unit of the printer and slide the
harness cover up to remove it.
Process the harness cover as
shown in the illustration.
Harness cover
Screw
Mounting plates: 2 pcs.
Staple cartridge: 1 pc.
Tray 1: 1 pc.
Screws A (M4x8): 5 pcs.
Screw B: 1 pc.
<4> Open the front cover of the
finisher and fix the finisher with
three screws A at the positions
shown in the illustration.
Then, close the front cover and
close the paper tray of the
stand/paper drawer.
<5> Attach the mounting plates to the
positions shown in the illustration and
fix them with screws A.
10. Arrange the harness of the finisher.
<2> Connect the power supply
unit harness connector to CN11
(red connector) of the PCU PWB
of the main unit of the printer.
<3> Reattach the harness cover
to its original position and fix it
with the removed screw.
At this time, ensure that the
power supply unit harness is
arranged as shown in the
illustration.
Wire saddle
Harness cover
Optional power
supply harnesses
Screw
5. Attach the trays .
4. Insert the staple cartridge.
7. Attach the power supply unit.
Optional power supply unit
Screws
Screws
Connector
<1> Pass the harness of the
finisher between the power
supply unit and the frame of the
stand/paper drawer and connect
it to the connector of the power
supply unit.
<2> Fit the snap band attached to
the finisher at the position shown
in the illustration to fix the
harness.
<1> Connect the AC cord of
the power supply unit to the
inlet connector of the main
unit of the printer at the
location shown in the
illustration.
Remove the two screws that
secure the rear cabinet and
remove the rear cabinet.
Remove the screw that fixes the
AC inlet cover and then remove
the AC inlet cover.
Process the AC inlet cover as
shown in the illustration.
8. Connect the power supply unit harness to the PCU PWB
of the main unit of the printer.
<1> Pass the AC cord of the power supply
unit as shown in the illustration and fix the
rear cabinet of the stand/paper drawer with
the screws.
11. Attach the rear cabinet of the stand/paper drawer.
<2> Attach the AC inlet cover to
the rear cabinet of the
stand/paper drawer and fix it
with the removed screw.
Screw
AC inlet cover
AC cord
Cabinet
Mounting plates
Screws A
Screws A
Screws A
Snap band
Finisher harness
Installation is now complete.
Tray 1
Tray 2
• Start installation after checking that the DATA and COMMUNICATION
indicators on the operation panel are neither lit nor blinking.
• For installation of B83F, an optional stand/paper drawer (stand/MPD & 2000
sheet paper drawer, stand/3 x 500 sheet paper drawer or multi purpose drawer)
must have been installed.
Also if a multi purpose drawer has been installed, a power supply unit is
needed additionally.
<Before installation>
Tray 2: 1 pc.
"OFF"
Actuator
Relay unit
• Fix the harness securely to the
wire saddle.
FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS.
SEE OKI DIGITAL PRINTER SERVICE MANUAL OR
INSTALLATION MANUAL TO DETERMINE SUITABILITY.
Connect the AC cord of the optional power supply unit
to the main unit of the printer.
[Caution] Insert the mounting plate
under the desk frame.
(Front side)
(Rear side)
10. Remove the AC inlet cover and then remove the rear
cabinet of the stand/paper drawer.
<1> Remove the screw that
fixes the AC inlet cover and
then remove the AC inlet
cover.
<2> Remove the AC cord of the power
supply unit from the inlet connector of the
main unit of the printer.
Remove the four screws that fix the rear
cabinet and then remove the rear cabinet.
Screw
Screw
Screw
Screw
AC inlet cover
Rear cabinet
Rear cabinet
Rear
cabinet
Screw B
<1> Pull out the staple unit.
<2> Remove the sealing tape from the staple cartridge.
<3> Insert the staple cartridge.
<4> Slide the release lever to the left and return the staple unit.
Power supply unit
connector
[Caution]
Do not press on the relay unit
while it is raised.
(Doing so may deform or damage
the unit.)
Attach tray 1 and tray 2 to
the positions shown in the
illustration.
AC inlet cover
Wire saddle
(* Similar work for the multi purpose drawer)
(* Similar work for the multi purpose drawer)
(* Similar work for the multi purpose drawer)
Push.
Push.
Place.
Grip
Grip
Stand frame
Mounting plate
Cut out.
AC inlet cover
Attach the power supply unit to the brackets and secure it using the supplied
three screws.
CN11
Wire saddle
Stapling position labels:
2 sheets
Steps 6 and after are the procedure to be carried out when a multi
purpose drawer has been installed.
If a stand/MPD & 2000 sheet paper drawer or a stand/3 x 500 sheet
paper drawer has been installed, carry out steps 9 and after.
Bracket
Bracket
10