Filter
Top Products
B83TT Installation Manual
<Parts included>
1. Turn off the main switch of the main unit of the printer.
2. Attach the adjusters and adjust them.
3. Put the main unit of the printer on the stand/paper drawer.
<1> Pull out the paper tray of
the main unit until it stops and
then remove it by lifting both
ends of the tray.
<1> Insert the left adjusters to
the stand/paper drawer.
<2> Turn the five adjusters to
lower them until they touch the
floor.
<3> Attach the four adjuster
covers.
• Be sure to attach the left
adjuster to prevent
overturning.
[Caution] The lower tray
cannot be pulled out unless
the adjuster is lowered to
the specified position.
Turn the main switch located on the front side of the
printer to the "OFF" position.
Then remove the power plug from the outlet.
Attach the two rear mounting
plates using a supplied
screw for each.
4. Connect the main unit to the stand/paper drawer.
6. Attach the power supply unit.
7. Connect the power supply unit harness to the PCU PWB
of the main unit of the printer.
8. Connect the relay harness of the stand/paper drawer
to the power supply unit.
<1> Pass the cord of the power supply
unit through the hole of the rear cabinet
and attach the rear cabinet to the
stand/paper drawer.
9. Attach the rear cabinet of the stand/paper drawer.
Connect the AC cord of the
power supply unit to the inlet
connector of the main unit of
the printer at the location
shown in the illustration.
10. Connect the AC cord of the power supply unit to the
main unit of the printer.
<1> To use the setting mode, insert the power plug of the main unit of the
printer to the outlet and turn the main switch on while pressing the [MENU]
key and the [OK] key of the operation panel of the main unit of the printer.
<2> After pressing the [MENU] key several times to display "SIZE
ADJUSTMENT A" in the message display and press the [OK] key.
<3> "MAXIMUM SIZE" is displayed.
Pull out the paper tray and extend the paper guides to the maximum.
Then, return the paper tray into the unit and press the [OK] key.
<4> "MINIMUM SIZE" is
displayed. Pull out the paper
tray again and narrow the
paper guides to the minimum.
Then, return the paper tray into
the unit and press the [OK] key.
(The rear guide need not be
adjusted.)
[Caution]
If the setting above is not
carried out, the paper detection
function will not operate.
11. Adjust the position of the paper guides of the
upper paper tray of the stand/paper drawer.
"OFF"
<2> Hold the main unit of the
printer at the positions shown
in the illustration and put the main unit on the
stand/paper drawer so that the front side and
the left side of the main unit are aligned to
those of the stand/paper drawer.
Front side
Rear side
<2> Remove the screw that fixes
the AC inlet cover and then remove
the AC inlet cover.
<3> Cut out the AC inlet cover as
shown in the illustration.
5. Remove the rear cabinet of the stand/paper drawer and
remove the AC inlet cover.
AC inlet cover
Cut out.
Power supply unit
Screws
Screws
<1> Remove the screw that
fixes the harness cover of the
main unit of the printer and
slide the harness cover up to
remove it.
<3> Reattach the harness
cover to its original position and
fix it with the removed screw.
At this time, ensure that the
optional power supply unit
harness is arranged as shown
in the illustration.
Connector
Wire saddle
Harness cover
Harness cover
Optional power
supply harness
Screw
Cut out.
Screw
Left adjuster: 1 pc.
Front mounting
plates: 2 pcs.
Rear mounting
plates: 2 pcs.
Adjuster covers: 4 pcs.
Screws (M4x8):
4 pcs.
<1> Remove the four screws that
fix the rear cabinet and then
remove the rear cabinet.
<2>Pull out the upper tray of
the stand/paper drawer until
it stops, and attach the two
front mounting plates using
a supplied screw for each.
Then, remove the lock of the
paper tray and close the
tray.
Remove the locks of the
middle tray and the lower
tray similarly.
AC cord
1
2
2
2
2
3
3
4
3
Rear mounting plate
Rear mounting plate
Screw
Screw
Screw
Screw
Front
mounting plate
Front mounting plate
Rear cabinet
Rear cabinet
Screw
AC inlet cover
<2> Attach the AC inlet cover
to the rear cabinet of the
stand/paper drawer and fix it
with the removed screw.
Connect the relay harness of
the stand/paper drawer to the
connector of the power supply
unit.
Connector of the power supply connector
Relay harness of the
stand/paper drawer
Installation is now complete.
<3> Reattach the paper tray
of the main unit.
FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS.
SEE OKI DIGITAL PRINTER SERVICE MANUAL OR
INSTALLATION MANUAL TO DETERMINE SUITABILITY.
[Caution]
For installation of the main unit, it must be
held by two persons and installed carefully.
[Caution]
Insert the rear mounting plates
under the Stand frame.
Attach the power supply unit to the brackets and secure it using the three
supplied screws.
Bracket
Cut out the harness cover as
shown in the illustration.
CN11
13. Carry out the off center adjustment.
Stand frame
Mounting plate
Paper guides
Wire saddle
<2> Connect the optional
power supply harness
connector to CN11 (red
connector) of the PCU PWB of
the main unit of the printer.
• Fix the harness securely to
the wire saddle.
<Before installation>
•
Start installation after checking that the DATA and
COMMUNICATION indicators on the operation panel are
neither lit nor blinking.
• For installation, a power supply unit (AR-DC1) is needed.
Bracket
* If another peripheral device must be installed, carry out
the following step at the end of the installation work.
Rear guide
4