Filter
Top Products
Staple unit
Screws
Front cabinet
Parts included
1. Turn off the main switch of the main unit of the printer.
2.
Remove the front cover from the right front of the finisher.
Turn the main switch located
on the front side of the main
unit to the "OFF" position.
Then remove the power plug
of the main unit from the outlet.
Loosen the screw and remove
the connector of the finisher.
"OFF"
Screw
(M4 x 6 with rosette)
: 1 pc.
Harness A (purple): 1 pc.
Harness B (orange): 1 pc.
Dust box label:
1 sheet
<1> Remove the four top cover
securing screws and remove the top
cover.
8. Reattach the front cover to the right front of the finisher.
7. Reattach the covers that have been removed.
6. Connect the harness of the punch module to the PWB
of the finisher.
5. Attach the punch module.
4. Remove the top cover.
Installation is now complete.
Screws B
Screws A
Front cover
<3> Remove the three screws
that fix the rear cabinet and
remove the rear cabinet.
At this time, remove the relay
harness through the opening
of the rear cabinet.
<1> Open the front
door of the finisher and
remove the jam
handling dial.
3. Remove the front cabinet and the rear cabinet from
the finisher.
Jam handling dial
Staple unit
Screws
Screws
Front cabinet
Screw
Relay harness
Opening for
relay harness
Screw
Rear
cabinet
Screw
Relay harness
Opening for
relay harness
Screws
Rear cabinet
<2> Remove the four pawls
from the top cover and
separate the cover into the
upper and lower portions.
Reuse the upper portion.
Top cover
Lock release lever (A)
Projection (B)
Latch arm
Pawl (D)
Screw
Screw
Top cover
<Before installation>
For installation of B83THP / USP / FHP / FBP, a saddle stitch
finisher B83SS must have been installed.
<2> Remove the four front
cabinet securing screws, pull
out the staple unit until it stops,
then remove the pawl of the
front cabinet in the direction
indicated by the arrow and
remove the front cabinet.
<4> Remove the three rear
cabinet securing screws,
remove the pawl in the
direction indicated by the
arrow, and remove the rear
cabinet.
At this time, remove the relay
harness through the opening
of the rear cabinet.
Screws
Connector
AC cord
Hole punch position label:
2 sheets
Screws
Connector
Pawl
Pawl
9. Paste the dust box label to the top cover.
Remove the clamps that fix
the harness, handle the wiring
of harness A (purple) and
harness B (orange), and fix
them with the clamps.
Paste the supplied dust box
label to the location indicated
in the illustration.
<1> Insert the two bosses of the punch unit into the boss holes of the
finisher and fix the punch module using three screws.
(Note)
For the screws, use a supplied screw and the two screws that have been
removed in step 4.
Top cover
Screws
Boss
Boss hole
Boss
Boss hole
Screw (with rosette) (supplied with this module)
Screw
Screw
Punch module
<4> Reattach the jam
handling dial and close the
front cover.
Clamps
Clamps
Harness A (purple)
Harness B (orange)
Harness A (purple)
Harness B (orange)
Jam handling dial
B83THP / USP / FHP / FBP
Installation Manual
FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS.
SEE OKI DIGITAL PRINTER SERVICE MANUAL OR
INSTALLATION MANUAL TO DETERMINE SUITABILITY.
10. Connect the connector to the stand/paper drawer and
connect the AC cord of the power supply unit to the
main unit of the printer.
Connect the connector of the
relay harness of the finisher to
the stand/paper drawer and
tighten the screws of the
connector.
(C)
Remove the screws A and B
(two for each) that secure the
finisher front cover and
remove the front cover.
Screws B
Screws A
Front cover
Pawl
Pawl
<1> Hang the two pawls of
the top cover and secure
them using the two screws.
<2> Pass the relay harness to
the rear cabinet and secure
the rear cabinet using the
three screws.
<3> Remove the lock release
lever that has been attached
to the front cabinet.
Reattach the front cabinet to
its original position, push in
the staple unit, and attach it
using the two screws.
Insert the protrusion (B) of the
lock release lever that has
been removed before to the
hole (C) of the latch arm.
After attaching it, move the
lever to check that it moves
smoothly.
If the lever does not move
smoothly, remove the lock
release lever by releasing the
pawl at the lower part of the
lock release lever using a flat-
blade screwdriver or the like
and then insert it again.
Attach the front cover using
the screws A and B (two for
each).
Pawl
12