Filter
Top Products
B83DB Installation Manual
5. Attach the exit tray.
6.
Adjust the position of the paper guides of the bypass tray.
1. Turn off the main switch of the main unit of the printer.
2.
Remove the left side cover of the main unit of the printer.
Turn the main switch located on the front side of the
main unit of the printer to the "OFF" position.
Then, remove the power plug of the main unit of the
printer from the outlet.
Unlock the lock release lever of the
main unit of the printer and then pull
out the left door.
Slide the two upper covers up to
remove them. Remove the lower
cover by inserting a flat-blade
screwdriver at three locations ( )
shown in the illustration.
Then, close the left door.
<1> Hang the hooks located at
the upper part of the duplex
module on the openings of the
left door of the main unit of the
printer.
<2> Push the lower part of the
duplex module to insert the
positioning bosses securely into
the main unit of the printer.
<3> Tighten the two screws built
in the duplex module.
3.
Attach the duplex module to the main unit of the printer.
<1> Remove the screw that
fixes the harness cover of the
main unit of the printer and
then slide the harness cover
up to remove it.
4. Connect the harness to the main unit of the printer.
Top covers
Lower cover
Left door
<3> Connect the connector of
the relay harness of the
duplex module to the CN12
(white connector) of the PCU
PWB of the main unit of the
printer.
<4> Insert the snap bands to
the locations shown in the
illustration and fix them.
<5>Secure the earth harness
using the supplied M4 screw.
<2> Process the harness cover
as shown in the illustration.
<6> Reattach the harness cover
to its original position and fix it
with the removed screw.
"
OFF
"
Lock release lever
Harness cover
Screw
Harness cover
Screw
Cut out.
Harness cover
Hook
Positioning boss
Positioning boss
Hook
Duplex module
Parts included
Exit tray
Relay harness
<1> To use the setting mode, insert the power plug of
the main unit of the printer to the outlet and turn the
main switch on while pressing the [MENU] key and
the [OK] key of the operation panel of the main unit of
the printer.
<2> After pressing the [MENU] key several times to
display "SIZE ADJUSTMENT A" in the message
display, press the [ ] key to display "SIZE ADJUSTMENT B" and press the
[OK] key.
<3> "MAXIMUM SIZE" is displayed.
Since "MAXIMUM SIZE" is displayed with a number, press the [ ] key or the
[ ] key to change the number so that the number is equal to the value of
[MAX] written on the label
( NOTE)
and then press the [OK] key.
<4> Since "P1 SIZE" is displayed with a number, press the [ ] key or the [ ]
key to change the number so that the number is equal to the value of [P1]
written on the label
( NOTE)
and then press the [OK] key.
<5> Since "P2 SIZE" is displayed with a number, press the [ ] key or the [ ]
key to change the number so that the number is equal to the value of [P2]
written on the label
( NOTE)
and then press the [OK] key.
<6> Since "MINIMUM SIZE" is displayed with a number, press the [ ] key or
the [ ] key to change the number so that the number is equal to the value of
[MIN] written on the label
( NOTE)
and then press the [OK] key.
[Caution]
If the setting above is not carried out, the paper detection function will not
operate.
"ON"
Label
( NOTE)
Illustration of label sticking position
Installation is now complete.
FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS.
SEE OKI DIGITAL PRINTER SERVICE MANUAL OR
INSTALLATION MANUAL TO DETERMINE SUITABILITY.
M4 Screws :
1 pcs.
<Before installation>
• Carry out the installation after checking that
the DATA indicator on the operation panel is
neither lit nor blinking.
• For installing B83DB, an optional desk (multi
purpose drawer, stand/3 x 500 sheet paper
drawer or stand/MPD & 2000 sheet drawer)
must have been installed.
• Ensure that the front mounting plates and
the rear mounting plates included with the
optional stand/paper drawer are securely
attached.
• Check that the left adjuster supplied with an optional stand/drawer
has been attached.
Relay harness
connector
PCU PWB
Snap bands
Ground harness
M4 Screw
CN12
7. Carry out the off center adjustment.
MAX MINP1 P2
(Back surface of the bypass tray
extension)
* If another peripheral device must be installed, carry out
the following step at the end of the installation work.
8