Filter
Top Products
Network setup (CLP-320N(K)/CLP-321N/CLP-325W(K)/CLP-326W only)_ 35
Printing network configuration report
You can print a Network Configuration Report from the machine's control
panel that will show the current machine’s network settings. This will help
you to set up a network and troubleshoot problems.
To print the report:
In ready mode, press and hold the
(cancel button) for about 5 seconds.
You can find your machine’s MAC address and IP address.
For example:
• MAC
Address: 00:15:99:41:A2:78
• IP Addre
ss: 192.0.0.192
Setting IP address
Firstly, you have to set up an IP address for network printing and
managements. In most cases a new IP address will be automatically
assigned by a DHCP (Dynamic Host Configuration Protocol) server located
on the network.
In a few situations the IP address must be set manually. This is called a
static IP and
is often required in corporate Intranets for security reasons.
• DHCP IP a
ssignment: Connect your machine to the network, and wait a
few minutes for the DHCP server to assign an IP address to the
machine. Then, print the Network Configuration Report as explained
above. If the report shows that the IP address has changed, the
assignment was successful. You will see the new IP address in the
report.
• Sta
tic IP assignment: Use SetIP program to change the IP address
from your computer.
In an office environment, we recommend that you contact a network
a
dministrator to set this address for you.
IPv4 configuration
IPv4 setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your
machine using its MAC address to communicate with the machine. A
MAC address is the hardware serial number of the network interface and
can be found in the Network Configuration Report.
For using SetIP program, disable the co
mputer firewall before continuing
by performing the following:
1.Ope
n Start > Control Panel.
2.Doub
le click Security Center.
3.Click F
irewall.
4.Disabl
e the firewall.
Installing the program
1.Insert the Printer Software CD-ROM provided with your machine.
When the driver CD runs automatically, close that window.
2.Start Windows Explorer and open the X drive. (X represents your
CD-ROM drive.)
3.Doub
le-click Application > SetIP.
4.Doub
le-click Setup.exe to install this program.
5.Select a
language, then click Next.
6.Fol
low the instructions in the window and complete the installation.
Starting the program
1.Connect your machine to the network with a network cable.
2.Turn
ed on the machine.
3.From th
e Windows Start menu, select All Programs > Samsung
Printers > SetIP > SetIP.
4.Click on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5.En
ter the machine’s new information into the configuration window as
follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
•MAC Address: Find the machine’s MAC address from the Network
Configuration Report and enter it without the colons. For
example, 00:15:99:29:51:A8 becomes 0015992951A8.
•IP Ad
dress: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150,
enter 192
.168.1.X. (X is number between 1 and 254 other than
the computer’s address.)
•Subnet Mask:
Enter a Subnet Mask.
•Def
ault Gateway: Enter a Default Gateway.
6.Click Ap
ply, and then click OK. The machine will automatically print
the Network Configuration Report. Confirm that all the settings are
correct.
7.Click Exit to
close the SetIP program.
8.If necessary, restart the
computer’s firewall.
IPv4 setting using SetIP Program (Macintosh)
For using SetIP program, disable the computer firewall before continuing
by performing the following:
The path and UIs may differ by Mac OS version. Refer to the Mac
OS manual.
1.Open System Preferences.
2.Click Security.
3.Click the Fi
rewall menu.
4.Turn firewall off.
The following instructions may vary for your model.
1.C
onnect your machine to the network with a network cable.
2.Insert th
e Installation CD-ROM, and open the disk window, select
MAC_Installer > MAC_Printer > SetIP > SetIPApplet.html.
3.D
ouble click the file and Safari will automatically open, then select
Trust. The browser will open the SetIPApplet.html page that shows
the printer’s name and IP address information.
4.Click on
the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5.Enter the machine’s new information into the configuration window as
follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
•MAC A
ddress: Find the machine’s MAC address from the Network
Configuration Report and enter it without the colons. For