Filter
Top Products
Using Your Printer on a Network (CLP-600N only)
8.
3
13
Repeat step 12 to complete the address from the 1st byte
to the 4th byte.
14
To select other parameters, such as the Subnet Mask or
Gateway, press the scroll button ( or ). Press the
Enter
button ( ).
15
Repeat steps 12 through 13 to configure the other TCP/IP
parameters.
16
Press the
On Line/Continue
button ( ) to return to
ready mode.
Dynamic Addressing (BOOTP/DHCP)
To assign the TCP/IP address automatically by the server, take
the following steps:
1
In ready mode, press the
Menu
button ( ) until you see
“Network” on the bottom line of the display. Press the
Enter
button ( ) to access the menu.
2
Press the
Enter
button ( ) when “Config Network”
displays on the bottom line.
3
Press the scroll button ( or ) until “Yes” displays,
and press the
Enter
button ( ).
4
Press the
Upper Level
button ( ), then use the scroll
button ( ).
5
Press the
Enter
button ( ) when “Config TCP” displays.
6
Press the scroll button ( or ) until “Yes” displays,
and press the
Enter
button ( ).
7
Press the
Upper Level
button ( ), then use the scroll
button ( ).
8
Press the
Enter
button ( ) when “IP Get Method”
displays.
9
Press the scroll button ( or ) until “DHCP” displays,
and press the
Enter
button ( ).
10
To assign the address from the BOOTP server, press the
Enter
button ( ) when “BOOTP” displays.
11
Press the
On Line/Continue
button ( ) to return to
ready mode.
Configuring IPX Frame Types
On IPX/SPX protocol networks (for example, Novell NetWare),
the format of the network communication frames must be
specified for the printer. In most cases, you can keep the ‘Auto’
default setting. However, you can manually set the frame type
format, if required.
•
Auto
(default): Automatically senses and limits the frame
type to the first one detected.
•
EN_8022
: Limits the frame type to IPX over IEEE 802.2
with IEEE 802.3 frames. All others will be discarded.
•
EN_8023
: Limits the frame type to IPX over IEEE 802.3
frames. All others will be discarded.
•
EN_II
: Limits the frame type to IPX over Ethernet Frames.
All others will be discarded.
•
EN_SNAP
: Limits the frame type to IPX over SNAP with
IEEE 802.3 frames. All others will be discarded.
Note that the IPX/SPX protocol must be enabled in the
Netware
menu before you can configure frame types. See
“Setting Network Protocols” on page 8.2.
Take the following steps to change the frame type format:
1
In ready mode, press the
Menu
button ( ) until you see
“Network” on the bottom line of the display. Press the
Enter
button ( ) to access the menu.
2
Press the
Enter
button ( ) when “Config Network”
displays on the bottom line.
3
Press the scroll button ( or ) until “Yes” displays on
the bottom line. Press the
Enter
button ( ).
4
Press the
Upper Level
button ( ).
5
Press the scroll button ( or ) until “Netware”
displays on the bottom line. Press the
Enter
button ( ).
6
Press the scroll button ( or ) until “On” displays on
the bottom line. Press the
Enter
button ( ).
7
Press the
Upper Level
button ( ), then use the scroll
button ( ).
8
Press the
Enter
button ( ) when “Config Netware”
displays.
9
Press the scroll button ( or ) until “Yes” displays on
the bottom line. Press the
Enter
button ( ).
10
Press the
Upper Level
button ( ), then use the scroll
button ( ).
11
Press the
Enter
button ( ) when “IPX Frame Type”
displays.