Filter
Top Products
[9] USER PROGRAM
The factory setting can be changed according to the operating conditions.
1. User program functions
Function Outline Default
Auto clear When a certain time is passed after completion of the machine operation, the mode is
returned to the initial state automatically.
The time to return to the initial state can be set in the range of 30 ~ 120 sec by the unit of 30
sec. This function can be canceled.
60 sec
Pre-heat When the machine is left unused with the power ON, the power consumption level is
automatically lowered to about 60Wh (*1). The time to operate this function can be set in
the range of 30 sec ~ 120 sec by the unit of 30 sec. This function can be canceled.
When this function operates, the pre-heat lamp on the operation panel lights up.
To cancel the pre-heat state, press any key on the operation panel.
(When the START key is pressed, pre-heat is canceled and copying is started,)
This function is canceled with the document is set or the tray is pulled out.
90 sec
Auto power shut off passing time When the machine is left unused with the power ON, the power consumption is
automatically lowered to about 4.8Wh (*1). The time to operate this function can be set in
the range of 30 min to 240 min. When this function operates, all the lamps except for the
pre-heat lamp turn off.
To cancel the auto power shut off state, press the START key.
30 min
Stream feeding mode (with
SPF/R-SPF installed)
After making copy with SPF/R-SPF, the document feed display lamp blinks, set the
document, and the document is automatically fed.
Cancel
Auto power shut off setting The auto power shut off function can be canceled. Setting
2 in 1/4 in 1 solid line frame setting
(with electronic sort board,
SPF/R-SPF installed)
Images on two or more pages are copied on one sheet of paper (2 in 1/4 in 1). When this
function is used, copying can be made with the solid lines at the boundaries of images.
Setting
Rotation copy
(With electronic sort board installed)
When the paper auto selection function is operating, if there is no paper of the suitable size
or the suitable direction, paper of the same size but of different direction is automatically
selected and the document images are rotated by 90 degrees to copy.
The magnification ratio auto select function operates and rotates document images by 90
degrees to make proper copy when the document images and the paper direction differ from
each other.
Cancel
Paper auto selection The paper of the same size as the document size selected by the document size set key
(A3, B4, A4, A4R, B5, B5R 11" × 17", 8.5" × 14", 8.5" × 13", 8.5" × 11", 8.5" × 11"R, 8.5" ×
5.5" only) is automatically selected. This function is canceled.
Setting
Tray auto selection (with 1-step
paper feed unit, 2-step paper feed
unit installed)
The paper of the same size as the document size selected by the document size set key
(A3, B4, A4, A4R, B5, B5R 11" × 17", 8.5" × 14", 8.5" × 13", 8.5" × 11", 8.5" × 11"R, 8.5" ×
5.5" only) is automatically selected. This function is canceled.
Setting
Department counter Refer to "3. Department counter setting."
Edge erase (with electronic sort
board installed)
Shades around images and shades at the binding margin can be erased by this function.
The erase range can be set in the range of 0 ~ 20mm by the unit of 5mm.
10mm
2 in 1 layout (with electronic sort
board, SPF/R-SPF installed)
The layout pattern for copying images of two pages on one page can be selected. Pattern A
4 in 1 layout (with electronic sort
board, SPF/R-SPF installed)
The layout pattern for copying images of four pages on one page can be selected. Pattern A
*1: The power consumption in pre-heat, auto power shut off depends on the operating conditions.
Pattern A
Pattern B
Pattern A Pattern B Pattern C Pattern D
AR-161
AR-160/161 FM/E [9] USER PROGRAM 11/27/1998
9 – 1