Filter
Top Products
26
D:\SDM\n80\N80GB\001009\3868361251\386836125SDMN50AEP\02GB-
SDMN50AEP\01GB02BAS-AEP.fm
masterpage:Left
SDM-N80
4-082-671-12(1)
Self-diagnosis function
Thismonitorisequippedwitha self-diagnosisfunction.Ifthere is
a problem with your monitor or computer(s), the screen will go
blank and the 1 (power) indicator will either light up green or
flash orange. If the 1 (power) indicator is lit in orange, the
computer is in power saving mode. Try pressing any key on the
keyboard or moving the mouse.
If the 1 (power) indicator is green
1 Turn off the AC power switch and disconnect the
video signal cables from the INPUT1 and INPUT2
connectors of the media engine.
2 Pressthe AC powerswitch twice to turnthe monitor
off and then on.
If all four color bars appear (white, red, green, blue), the monitor
is working properly. Reconnect the video input cables and check
the condition of your computer(s).
If the colorbars donot appear, thereis a potential monitorfailure.
Inform your authorized Sony dealer of the monitor’s condition.
If the 1 (power) indicator is flashing orange
Press the 1 (power) switch twice to turn the display off
and then on.
If the 1(power)indicator lights upgreen,the monitoris working
properly.
If the 1 (power) indicator is still flashing, there is a potential
monitor failure. Count the number of seconds between orange
flashes of the 1 (power) indicator and inform your authorized
Sony dealer of the monitor’s condition. Be sure to notethe model
name and serial number of your monitor. Also note the make and
model of your computer and graphics board.
Specifications
LCD panel Panel type: a-Si TFT Active Matrix
Picture size: 18.1 inch (46 cm)
Input signal format RGB operating frequency*
Horizontal: 28 – 92 kHz**
Vertical: 48 – 85 Hz**
Resolution** Horizontal: Max.1280 dots
Vertical: Max.1024 lines
Video input connector Analog RGB: HD15
Digital/analog RGB: DVI-I 29 pins
Input signal levels Analog RGB video signal
0.700 Vp-p, 75 Ω, positive
SYNC signal
TTL level, 2 kΩ,
positive or negative
(Separate horizontal and vertical,
or composite sync)
0.3 Vp-p, 75 Ω, negative
(Sync on green)
Digital RGB (DVI) video signal
TMDS (Single link)
Audio output 1 W × 2
Headphones jack Stereo minijack
Accepts impedance of 16 – 48 Ω
AUDIO IN jacks Stereo minijack × 2
Accepts impedance of 47 kΩ
Accepts level 0.5 Vrms
Power requirements 100 – 240 V, 50 – 60 Hz, 0.7 – 0.4 A
Power consumption Max. 67 W
Operating temperature 5 – 35
°C
Dimensions (w/h/d) Display (upright and in the lowest
position):
Approx. 432 × 400 × 195 mm
(17
1
/8
× 15
3
/4
× 7
3
/4 inches)
Media engine:
Approx. 94 × 212 × 204 mm
(3
3
/4
× 8
3
/8
× 8
1
/8 inches)
Mass Display:
Approx.6.5kg(14lb5oz)
Media engine:
Approx. 1.5 kg (3 lb 5 oz)
Plug & Play DDC2B
Accessories See page 7.
* Recommended horizontal and vertical timing condition
• Horizontalsyncwidthdutyshouldbemorethan4.8%oftotal
horizontal time or 0.8 µs, whichever is larger.
• Horizontal blanking width should be more than 2.5 µsec.
• Vertical blanking width should be more than 450 µsec.
**A 1600 × 1200 resolution signal is displayed provisionally as
long as its horizontal and vertical frequencies are lower than
the following values.
• Analog RGB signal: Horizontal 107 kHz, Vertical 85 Hz
• Digital RGB signal: Horizontal 75 kHz, Vertical 60 Hz
Design and specifications are subject to change without notice.
1 (power)
indicator
01GB01COV-AEP.book Page 26 Monday, July 16, 2001 2:22 PM