Filter
Top Products
12 MI.20xx Manual
Hardware information Introduction
Dynamic Parameters
Dynamic parameters are measured at ± 1 V input range (if no other range is stated) and 50 Ohm termination with the samplerate specified in the table. Measured parameters are avera-
ged 20 times to get typical values. Test signal is a pure sine wave of the specified frequency with > 99% amplitude. SNR and RMS noise parameters may differ depending on the quality
of the used PC. SNR = Signal to Noise Ratio, THD = Total Harmonic Distortion, SFDR = Spurious Free Dynamic Range, SINAD = Signal Noise and Distortion, ENOB = Effective Number
of Bits. For a detailed description please see application note 002.
Order information
MI.2020
MI.2021
MI.2030
MI.2031
max internal clock 50 MS/s 200 MS/s
max external clock 50 MS/s 100 MS/s
-3 dB bandwidth > 25 MHz > 90 MHz
MI.2020
MI.2021
MI.2030
MI.2031
Test - Samplerate 50 MS/s 100 MS/s
Testsignal frequency 1 MHz 1 MHz
SNR (typ) > 47.5 dB > 45.9 dB
THD (typ) < -52.5 dB < -49.1 dB
SFDR (typ), incl harm. > 57.0 dB > 55.5 dB
SINAD (typ) > 46.0 dB > 44.2
ENOB (based on SINAD) > 7.3 > 7.1
Order No Description Order No Description
MI2020 MI.2020 with 16 MSample memory and drivers/SBench 5.x MI2xxx-32M Option: 32 MSample memory instead of 16 MSample standard mem
MI2021 MI.2021 with 16 MSample memory and drivers/SBench 5.x MI2xxx-64M Option: 64 MSample memory instead of 16 MSample standard mem
MI2030 MI.2030 with 16 MSample memory and drivers/SBench 5.x MI2xxx-128M Option: 128 MSample memory instead of 16 MSample standard
mem
MI2031 MI.2031 with 16 MSample memory and drivers/SBench 5.x MI2xxx-256M Option: 256 MSample memory instead of 16 MSample standard
mem
MI2xxx-512M Option: 512 MSample memory instead of 16 MSample standard
mem
MI2xxx-smod Star Hub: Synchronisation of 2 - 16 boards, one option per system MI2xxx-up Additional handling costs for later memory upgrade
MIxxxx.xio Extra I/O, internal connector: 16 DI/O, 4 Analog out
MIxxxx-xmf Extra I/O, external connector: 24 DI/O, 4 Analog out, incl. cable MI2xxx-mr Option Multiple Recording: Memory segmentation
MI2xxx-time Timestamp option: Extra memory for trigger time MI2xxx-gs Option Gated Sampling: Gate signal controls acquisition
MI2xxx-cs Synchronisation of 2 - 4 boards, one option per system
Cab-3f-9m-80 Adapter cable: SMB female to BNC male 80 cm
Cab-3f-9m-200 Adapter cable: SMB female to BNC male 200 cm MI20xx-dl DASYLab driver for MI.20xx series
Cab-3f-9f-80 Adapter cable: SMB female to BNC female 80 cm MI20xx-hp VEE driver for MI.20xx series
Cab-3f-9f-200 Adapter cable: SMB female to BNC female 200 cm MI20xx-lv LabVIEW driver for MI.20xx series
MATLAB MATLAB driver for all MI.xxxx, MC.xxxx and MX.xxxx series.