Filter
Top Products
Safety Instructions
5975288 BARCOGRAPHICS 8200 110497
1-9
Safety Instructions
5975288 BARCOGRAPHICS 8200 110497
1-9
* To disconnect the cord, pull it out by the plug. Never pull the cord
itself.
* If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the
extension cord does not exceed the extension cord ampere rating.
Also make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes.
* Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
* Never spill liquid of any kind on the product. Should any liquid or
solid object fall into the cabinet, unplug the set and have it checked
by qualified service personnel before resuming operations.
* Lightning - For added protection for this video product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent
damage to the projector due to lightning and AC power-line surges.
* To reduce the lamp heat of the projector, switch the projector
first
to stand-by and let the projector lamp cool down for at least 15
minutes. Then the projector may be switchedoff with the power
switch.
On Installation
* Do not place this projector on an unstable cart, stand, or table. The
projector may fall, causing serious damage to it.
* Do not use this projector near water.
* Use only the power cord supplied with your projector. While
appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the projector.
For a replacement power cord, contact your dealer.
* Slots and openings in the cabinet and the sides are provided for
ventilation; to ensure reliable operation of the projector and to
protect it from overheating, these openings must not be blocked or
covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This prod-
uct should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation or
enclosure unless proper ventilation is provided.
Surface
Air circulation
Build-in Dust filter
* To disconnect the cord, pull it out by the plug. Never pull the cord
itself.
* If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the
extension cord does not exceed the extension cord ampere rating.
Also make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes.
* Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
* Never spill liquid of any kind on the product. Should any liquid or
solid object fall into the cabinet, unplug the set and have it checked
by qualified service personnel before resuming operations.
* Lightning - For added protection for this video product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent
damage to the projector due to lightning and AC power-line surges.
* To reduce the lamp heat of the projector, switch the projector
first
to stand-by and let the projector lamp cool down for at least 15
minutes. Then the projector may be switchedoff with the power
switch.
On Installation
* Do not place this projector on an unstable cart, stand, or table. The
projector may fall, causing serious damage to it.
* Do not use this projector near water.
* Use only the power cord supplied with your projector. While
appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the projector.
For a replacement power cord, contact your dealer.
* Slots and openings in the cabinet and the sides are provided for
ventilation; to ensure reliable operation of the projector and to
protect it from overheating, these openings must not be blocked or
covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This prod-
uct should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation or
enclosure unless proper ventilation is provided.
Surface
Air circulation
Build-in Dust filter