Filter
Top Products
2-7
I
N
O
U
T
RE
M
O
TE
2
AC
IN
AUD
IO
A
U
D
IO
O
U
T
R
R
/Cr
G
/Y
B
/Cb
V
H/
H
V
R
L
/
MO
N
O
R
L
/M
O
N
O
R
L/M
O
N
O
L/
M
ON
O
DVI
RG
B O
U
T
RGB 1
RGB 2
VIDEO
S-VIDEO
AU
DIO
S
LO
T
1
S
L
O
T 2
4
3
IN
O
U
T
R
E
M
O
T
E
2
AC
IN
A
U
D
IO
A
U
D
IO
O
U
T
R
R
/
C
r
G
/
Y
B
/
C
b
V
H/HV
R
L/MONO
R
L/MONO
R
L/MONO
L/MONO
DV
I
R
G
B
O
U
T
RG
B 1
RG
B 2
V
ID
E
O
S-V
ID
EO
A
U
D
I
O
S
L
O
T
1
S
L
O
T
2
2
1
4. Reinstall the lens hood.
q Remove the front lens cap from the lens unit.
w Insert the lens hood so that the grooves on the 4 corners of the lens hood
are properly lined up with the 4 catches on the projector.
e Secure the 2 screws using the hexagonal driver.
This completes installation. If necessary, put the lens hood cap on the
lens hood.
3
PC CONTROL
IN
IN
OUT
OUT
SC TRIGGER REMOTE 2
REMOTE 1
LAN
AC IN
USB
(
M
OU
SE
/H
UB
)
USB
(
PC
)
PC CARD
1
2
A
U
D
IO
AUDIO OUT
R
R
/
Cr
G
/Y
B
/C
b
V
H
/H
V
R
L
/M
O
N
O
R
L
/M
O
N
O
R
L
/M
O
N
O
L
/M
O
N
O
D
V
I
RGB OUT
R
G
B
1
R
G
B
2
V
IDE
O
S
-V
ID
E
O
A
U
D
IO
SLOT 1 SLOT 2
2
P
C
C
O
N
T
R
O
L
I
N
IN
O
U
T
O
U
T
S
C
T
R
I
G
G
E
R
R
E
M
O
T
E
2
R
E
M
O
T
E
1
L
A
N
A
C
I
N
U
S
B
(
MOUSE/HUB
)
U
S
B
(
P
C
)
P
C
C
A
R
D
1
2
AUDIO
A
U
D
I
O
O
U
T
R
R/Cr
G/Y
B/Cb
V
H
/
H
V
R
L
/
M
O
N
O
R
L
/
M
O
N
O
R
L
/
M
O
N
O
L
/
M
O
N
O
DV
I
R
G
B
O
U
T
R
G
B
1
R
GB
2
V
IDE
O
S-V
ID
E
O
AUDIO
S
L
O
T
1
S
L
O
T
2
1
Lens shift defection switch
2. Installation
3. Mount the lens unit on the projector and connect the extension cable attached to the projector.
q Remove the lens cap from the rear end of the lens unit.
NOTE: Leave the front lens cap for protection while mounting the lens unit.
w Insert the lens unit so that the 4 screws on the lens unit are properly lined up with the 4 holes on the lens mount.
CAUTION:There is a lens shift detection switch for the moving gears of the lens shift motors used to reduce the risk of pinching fingers.
Do not defeat this feature.
e Secure the 4 screws using the hexagonal driver.
r Insert the connector of the lens unit fully into the socket of the extension cable attached to the projector.
NOTE: The GT13ZL, GT19ZL, GT24ZL and GT34ZL optional lenses have one connector. The B type lenses (GT13ZLB, GT24ZLB and GT34ZLB) and
GT20ZL have two connectors.
Insert the connector into the 4-pin socket located to the right of the lens when in desktop mode.